Search results

I will tell you that my set of Eaton springs are of great quality, ride great, and fit perfect. You also get what you pay for as they weren't the cheapest option. Your options for rear springs are very limited. The fronts you should have an easier time with an off the shelf spring but probably...

No problem

65 ft-lbs It's about half way down the page here: http://www.pirate4x4.com/tech/billavista/60_front/index.html Everything you would ever want to know about the Dana 60.

How is the truck's idle speed? I would imagine if it was on the low side, doing some technical hill descent would tax the engine by being hard on the brakes and steering. When my truck idled too low, it would almost stall just trying to park because I had my foot on the brake and was requesting...

I don't think your solenoid should be cycling on and off numerous times. I personally from what you just said would to install AC 60g's. For the $60 it will cost, you will have a better plug and will know if the plugs where the culprit. Kill two birds with one stone. If it still acts up, I would...

I use the VP Racing cans like these: http://autoplicity.com/1039278-vp-fuel-containers-3512-5-gallon-square-jug-red?1&gclid=CNvr0MLcgssCFQIfhgodHEYONA I'm sure some LEO may bust you for them not being DOT/EPA/blah blah blah approved. Yeah, they work and are cheap. Plus I can have multiple...

Dont' reinvent the wheel. Get a good quality AC Delco replacement. Thread the fitting on half way first before bolting the pump to the block, it will make life easier. It's not difficult to replace, it's that the location requires some flexibility to do. Once it is done you are good to go for...

Not that a SF 14 bolt is a huge upgrade but it's better than a 10 bolt by far. The front end you won't gain really anything other than a few extra lug nuts. The gearing will probably help and also let you run a slightly larger tire. I say go for it. It's just some time and money, the swap you...

I always recommend just starting from scratch. Pull your tank, inspect/replace the sock, replace all your flex lines, change/upgrade the filter, install a new AC Delco pump, and enjoy your many years of reliable service. It's the only way to eliminate the starting and running issues with the old...

Why not just pull your batts and install in CUCV B?

If its a clean rig that has been serviced properly and turn key...probably worth that especially if the rust/rot is very low. It all boils down to what you are willing to pay for it. Why not go in at $3300 and worse case meet him half way if he goes for it. Worst he can say is no.

Go through and check that all of your safety switches work and that the governor is getting power. More than likely one of the control units is junk. Mine worked for awhile and gave up a few months ago. I have a new governor coming in from B4THUNDR.

I would throw a DVOM or test light on it. If you are getting power and the high idle isn't engaging you know what needs to be done...

I think is more of a gearing selection issue. That transmission is basically a 3 speed for most driving instances. You can only do so much with 3 gears in a manual trans. I agree that a splitter or maybe an NV4500 would do you a lot of good to keep things in the sweet spot. Even with an M1009...

I remember reading that GM no longer used them because it promoted cracking.

I don't think you can group a TH400 with modern transmissions. Its an apples to orange comparison. The TH400 is a dumb simpson planetary design with only a few inputs to control shifting...period. I'm sure transmission fluid temp is important to a degree but guys, this isn't rocket science. Put...

I vote for the cheapest way out to be putting one before the radiator to shed as much heat as possible and let the radiator cooler ensure the trans fluid is at operating temp. If you have money to burn, buy a completely independent fan cooled unit with a thermostat and have a temp gauge for...

I did one a few years back from a local Stanadyne certified dealer, it was competitive at $450-500. I bought the seal kit and was thinking of doing mine but after 30 years of service and being that it is the heart of the fuel system, I decided to bite the bullet and just installed a reman'd unit.

I've used these on my Samurai and they work great. Unfortunately they did not fit over my D60 front hub so I couldn't use them on my M1031. I will have to bore out the center but they do fit 6x5.5 pattern. They will pay for themselves with your first alignment...

A lot of the big shows are nothing more than parts pushers. All the builds incorporate the parts from the sponsors. I understand why but it doesn't present any cool fabrication. The powerblock shows are decent about getting the tech in somewhere. I've found myself watching the Motortrend...