Search results

My transfer is leaking and I have to replace the seal. I am looking for item 19 in figure 101. TM -34P // NSN 5330-00-079-1919 // P/N 11601229 // Seal, Plain Encased; Yoke Rear Is there any known source where I can buy one or any equivalent from the civilian market?

Hello Everybody, From the manual TM -34P I can see two different u-joints for the Deuce used on the prop-shaft forward rear axel to rear rear axle and trans to front axle. I do not mean the bolted prop-shafts. The lubrication fitting is either straight or in an angle. In my Deuce i've the one...

Hi, Does anyone know of an inexpensive source or has a repair kit for the M35 LDS 427-2 engine? Complete kit with sleeve, piston, rings. Six needed. There was a complete set of six on ebay sold for $350. Memphis Equipment is asking $311 ea. which is $1,866 in total. P/N 5702644, NSN...

I need some help cleaning my data plates for the Garwood winch. I would like to make them readable again. Remove the old paint without destroying the original paint. In the past I was able to remove paint from my plastic vehicle models with brake fluid. Would that work here too? What are you...

I'm currently working on the vehicle cab and have a question about the routing of the handbrake cable. There is part 14 in the TM and I no longer know where to mount it. The hole pattern fits in the cab so that I could screw the plate on from below. But then I kink the handbrake cable...

Hi folks, It is cold outside and I have here a multifuel space heater with a spark plug defect. The heater was made by Hunter, NSN 4520-00-114-1055. The spark plug must be replaced. My first thought was, to search for the part number. I tried to find the manual for the heater online by using...

Ulf uploaded in 2014 the TM 9-2320-242-34 (Direct Support, General Support and Maintenance Manual) On page 1-9 there should be the wiring diagram for the tractor, engine compartment and carrier. Unfortunately these pages of the PDF are incomplete and don't show the complete picture. Can...

Today I wanted to wash and prepare the Goat for an event we have here next weekend. 1st start the Goat. Nothing happened. No instruments, no starter, absolutely nothing. So I took my M151 and the jump start cable. The goat starts immediately. But the instruments still don't work, the light...

I am in the middle of my M35A2 restoration. Where do I find the bolts for the propeller shafts? From the TM it is NSN 5306-00-752-1001, P/N 7521001. Thanks a lot in advance for your hints, Richard

I am still looking for the yoke assy P/N 11601566 (issue July 1976 TM -34P , figure 107, item 2). NOS or used is welcome. Would be great you guys have one for me or can tell me a source in the USA. Thanks for taking a look, Richard

Last Saturday I drove 80 miles with the Goat. No problems. On Sunday, after 1.5 miles of driving, there was a noise which I never heard before. I stopped and made a walkaround. Nothing to see. Shafts okay, engine oil level okay, cooling water level okay. So I continued my drive - with no noise...

I got some new wiper arms and wiper blades for my Goat. Unfortunately I cannot use and install them. The former owner installed civil wiper motors which I cannot identify. But they are not M561 related. Does somebody know, where I can find a wiper motor for the driver and passenger side? NOS or...

First I am not a guru in a vehicle's electricity. But I have a problem with my Goat where some help or a good advice might be very helpful. This is the situation: When I am on the brake pedal or setting the turn signal to the right, the bulb on the carrier's right hand (driver's side) is not...

Hi, After repairing my Goat's brakes in 2014 I had some fun in driving it. This year a friend of mine made new brake shoe pins for my Goat, because I wasn't able to find some. So I had to open all six drums again. And on the left front axle I found - again - mud and rust in the brake drum :-( ...

Just went thru the manual section of this site and found two times the TM -20. Unfortunately both threads are not allowing to download anything. I have a TM -20 here on my desk, but the electrical diagrams are incomplete. Seems to me somebody forgot to unfold them before pressing the Copy...

I had problems to get my wheel from the hub. Finally it happened and it was a little bit tricky. Thanks to Loctite :naner: which was helpful, too. Now the question. From the -34P I can see that it should be a bolt with a ribbed shoulder. But mine isn't ribbed. How can I get the bolt (steel)...

This weekend I finished the tear-down process of my Deuce and a Half. After the engine and the gear box were moved away, I saw that the frame on the right is following a bow. The frame on the left side is straight. This brings me to the question whether my Deuce had an accident in the past or...

Search for a lever for my S-280 shelter Hi, I am looking for a lever for my S-280 shelter. Any ideas where I can get one? Or does someone here has one (or two) for me?

Perhaps this has been asked earlier. Is there a good source where I can buy parts for the Gama Goat? Am looking for some parts because of a coming restoration project. TIA, Richard

During my Deuce restoration project I found this. The cab was having a sheet of metal over another sheet of metal, two layers. Is this normal? Or was this the try to repair something? I removed the outer layer and the inner layer is not as worst as I expected. Further the inner sheet of metal is...