Search results

The humvee tires will fit on a stock M880.But you cannot drive the truck. They will rub HARD on the steering linkage.You will need a 4 inch lift minimum to run them without rubbing. Also you will need to switch to a power steering unit.The manual steering linkage comes out the side of the box...

Well,It turn out to be a bad brake booster.

Bob,That was my original thought.I bought a rebuilt from NAPA and I thought it was bad,So I then bought a new production from Advanced and I,m getting the same results.I had this same issue on another truck a while back and after bleeding everything a thousand times I finally got a good pedal.

I will go thru the system again,And replace the hoses you mentioned.The last time I had this happen,It was a pin hole in the metal line on the frame behind the fuel tank.But I do not see any leakage here.

I,m working on a M882,Trying to get the brakes to work.I have replaced the rear shoes and wheel cylinders.Also the front calipers, pads and outer rubber hoses.Installed a brand new master cylinder.I,ve bleed the master cylinder and installed it and have bleed the entire brake system several...

Just a up date.I got the turn signals working.But,They do not work when the head lights are on????

Brake lights work fine.

Just checked the flashers and they work fine,But still no turn signals.

I have replaced the column signal harness with another one I had,Because the signal arm would not return after a turn.But,The signals did not work before I replaced this and I had hoped replacing the harness would cure this issue.I did get them to work for a very short period by messing with the...

I,ve got a 77 M882.All of the lights work on the truck as does the blackout light system.The issue is the turn signals do not work.I have replaced both flashers and all the bulbs in the truck still nothing.Do you think this is a main blackout light switch issue?or just a bad relay somewhere.I...

Well,I thought I had it.It ran fine for a while.But now its back.Stalls when I step on the gas.But it does run better when it is warmed up.I have 4 of these trucks and I've got to say they all have the Dodge "dead spot" when accelerating.This truck is by far the worst.It will idle just fine,But...

OK,I got it figured out.I took the top cover off the carb.Under the cover you can see the accelerator pump and the two thin needle valves that go up when you accelerate.You can make fine adjustments in here with two small screws.I played around with these adjustment screws until I was satisfied...

Yes it does.

Bob,Sorry I forgot to mention. The carb is brand new out of the box.The truck will drive fine,It is just hard to get it from a stand still to driving.I have to rev the engine and kind of neutral drop it to go.There is no putting it in gear and stepping on the gas.That is when it stalls.

I,m working on a M882.The truck runs and idles fine,But when I put it in drive and step on the gas pedal it will stall.Any ideas?? I,m thinking vacumn advance on the distributor maybe.

Yes,It has the blackout light system.

After a lot of wire tracing,I found that 2 wires in the junction block on the fire wall had been placed out of order.By this I mean the brown wire for the parking lights was in the wrong plug in the junction block.It appears to have been made like this as the wire harness was never molested.I...

I have a M882 which has no parking lights.All of the other lights work,dash headlights turn signals and brake lights.What will cause this to happen??

I got it running!I read your posts and they where very helpful.It was one of those little boxes by the fuel pump.I by passed it and now it runs fine

I just got a MEP 002A at auction and I'm having this same issue.It blows the DC control circuit breaker when I turn the start knob to prime.It will pre heat ,But that is it.As soon as I turn the switch to start it will immediately blow the breaker.Anyone have ideas??