Search results

we used one winch truck with gin poles to lift a d6c widepad (about 32000 lbs )with a blown engine first try it lifted the front wheels on the truck so we chained it down to the blade on a d8k and lifted it high enough to back a lowboy under it . remote operation wasnt an option that day , but...

yes thats exactly right, if you can run your bucket to scratch off a couple inches or less of dirt over a burried line you know what im talking about.

my back hoe and my winch on it have the same type manual valve block and if you are using a set of gin poles on an oilfield truck and need to move your load an inch or less you dont control it by engin rpm ,your engine is set to your gpm of your pump and you leave it set there and use your valve...

you will get complete control by fethering the valve but it will take a bit of practice, watch sombody using an older backhoe they can move the boom with perfect control and there are fethering the valves .you can put in a variable flow control valve if you feel you need one . and i would not...

sephirothg hope you get your project done to your satisfaction . hyds are simple but its hard to find any firsthand knowledge of what works . dont worry about eficiencies if the company says it is so much tourqe at so much pressure its usualy so close as not to be worried about they take...

mudslinge never in anybodys postes are they recomending getting rid of the shear pin.its a saftey device and should not be screwed with you or sombody on here recomended drilling a hole throught the connector, if connecting the roller chain coupler that way was not self explanitory to you im not...

ya, sigh, i still would like one ot those 18s on the back of the deuce a winch on the back is so nice for hooking up 4 wheel trailers.

ya thats definatly a superior system but for other ppl the electric clutch could be an option

on a bought tank the inlet and outlet holes should be in the right places sometimes on homemade tanks the return is put to close to the suction and causes a bit of problems. im sure the tank should be fine your not using the winch for hours on end like you would use a brush cutter or slasher ...

if you have restrictors ( either drilled orifice or adjustable ) in your system you will generate lots of heat . if you have a big enough tank your oil will not get so hot . to small a tank with a big pump will cause cavitation( loss of prime or air in system) of your pump with the result of a...

if you go with hoses from one of the cheaper suppliers make sure you take double braid hose at least .. i like orb fittings for everything 35 ft lbs tourqe and no fooling with pipe thread or pipe goo.a bit more money over pipe fittings but neat looking and easy to adjust the lay of your hoses ...

if you can without to much trouble and it costing a fortune thats what i would do .. its just hard to replace parts that are obsolite,, for most ppl this site is super for finding parts .. and we bicker with each other but anybody on this site will go to almost any lengths to help another...

search is your frend and yes a 302 gasser does idle at 375 and a deuce winch is rated at 10 k max if you have to much more than that you will shear your pin or as some have found out blow up your winch and thats with either pto or hyd . im running motors that are 4500 psi on bush equipment...

we used a pump that size to make a metal bender and we ran a reduction of 5 to one with a 15 hp gas motor works ok but we sometimes stall it if we are not carefull. you pump will (if in good shape) keep max pressure no matter what your rpms are just your gallons per min will change.. do they...

thats a verry big pump way more than you need for a deuce winch that pump is the same size that our end dump gravel trucks use ,40 gpm at 3000 rpm you will probly need reastricrors in your lines or make sure not to rev it up and restrictors cause heat lots of heat. with that pump we use 35...

your deuce winch needs 145 ft lbs at the input shaft to pull 10000 lbs on the 4th wrap of cable (2343 divided by 12 =195 for the sharlyn)... at 800 rpm your pto is turning 520 rpm divide this by 23(worm gear reduction)( take diamiter of spool, times pi, times number of rpm your winch drum turns)...

sharlin has an 11.2 ci 15 gpm max 304 rpm 2343 inch lb at 1600 psi for around 225 bucks

the lovejoy can take lots of abuse if its perfectly lined up . mine kept breaking the spider into pieces and i couldnt get a big enough one with a small enough shaft hole . and didnt want to machine one out . so i went with the roller chain coupler its been on for over 150 hrs so far its pretty...

lovjoy coupler will never take the back and forth pressure i had them on my hyd for a while they didnt last very good . you can get an adaptor made at any machine shop or welding shop. google (roller chain coupler) to check them out

i think you could use that for a lot of 12 volt acceseries one toggle switch , power .no power should be easy to wire up