pa.rich
New member
- 1,323
- 9
- 0
I've got the truck sanded and primed
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M 211 SANDED AND PRIMED
- Thread starter pa.rich
- Start date
poppop
Well-known member
- 2,316
- 39
- 48
- Location
- Brooklet, Ga
Looking good!!!!
Capt.Marion
Active member
- 1,811
- 15
- 38
- Location
- Atlanta, GA
looks good!
alphadeltaromeo
Active member
- 1,901
- 3
- 38
- Location
- Alto, GA
Looks great...what color will the finished product be?
- 10,874
- 793
- 113
- Location
- Appomattox, VA
Is that a M211 or a M135? I only see one set of rear tires on there, not duals...
carmen
Member
- 72
- 0
- 6
- Location
- Pittston, Pa. 18640
Now that is coming along GREAT. I'm a little behind you - about a year. Stocking up on all the parts. We have to get together this summer.
Good Luck
Carmen
Good Luck
Carmen
- 5,273
- 4,089
- 113
- Location
- Charleston, WV
Re: RE: M 211 SANDED AND PRIMED
Keep up the good work pa.rich!
Looks to be a 211 running singles since there are no wheel-wells in the bed.maddawg308 said:
Keep up the good work pa.rich!
pa.rich
New member
- 1,323
- 9
- 0
RE: Re: RE: M 211 SANDED AND PRIMED
It is a XM211 . I painted it green today but the color is too light. Going to try a darker one tomorow. The green is simular to the color in the backround of these posts.No good. Rattle cans, dont have a sprayer yet. I will get it right eventually. It sure looks better than it did in the avatar though.
It is a XM211 . I painted it green today but the color is too light. Going to try a darker one tomorow. The green is simular to the color in the backround of these posts.No good. Rattle cans, dont have a sprayer yet. I will get it right eventually. It sure looks better than it did in the avatar though.
rtjraleigh
Banned
- 240
- 2
- 0
- Location
- SOUTH
any update photos
alphadeltaromeo
Active member
- 1,901
- 3
- 38
- Location
- Alto, GA
n1bnc
Member
- 275
- 0
- 16
- Location
- Somersworth, NH
Looking good!
I have wondered why the gods requested that the M135 bed be lower and require wheel wells compared to the seemingly cheaper to make M211 bed? Narrow I can understand, but why go to the expense of wheel wells?
Do you have the missing bits like the exhaust pipes and the passenger side step?
I have wondered why the gods requested that the M135 bed be lower and require wheel wells compared to the seemingly cheaper to make M211 bed? Narrow I can understand, but why go to the expense of wheel wells?
Do you have the missing bits like the exhaust pipes and the passenger side step?
pa.rich
New member
- 1,323
- 9
- 0
Yes they were taken off to straighten and sand and paint each piece. The exhaust is being painted with high heat paint . This truck is complete and original except for the M35 fuel tank and the roof. I shall replace both if I can come across the parts. I would also like to replace the drivers side fender that was hit one time.I am almost finished with the brakes and then shall start work on the inside. Parts I need are passenger side wiper air motor, Drivers side fender, M211 or simular fuel tank, hard top roof and cab back, but for now she looks pretty good for a 1952 M211. I would like to sell it in case someone is interested.
Attachments
pa.rich
New member
- 1,323
- 9
- 0
Oh, forgot, I installed a new lite switch and now the lites are working!
emr
New member
- 3,209
- 25
- 0
- Location
- landing , new jersey
WOW!!! It sure is awesome to see the GMC's getting the TLC they need and deserve!! Great Job!!! 
wsucougarx
Well-known member
- 6,949
- 63
- 48
- Location
- Washington State
Looks great!! Bravo Zulu