-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Rebuilding after 15 years of storage
- Thread starter PHOENIX-GER
- Start date
- 494
- 1,043
- 93
- Location
- Germany
Going on with a lot of small issues
First clean up the wiring at the steering column. We don't install the cover as we wait on the horn relais.
The speaker is now complete with the control lamp. We need to customize a cable with the correct connectors between cb radio and speaker to got it work
Going on with the registration plates of roadlicence for the civilian trailer hitch which we removed for rebuild
Also add the registration plate of the truck
Without this no roadregistration in Germany possible
The shipping data plate is not mandatory for roadregistration but it is necessary to have a high score in the oldtimer appraisel
This is the old mirrorglass. We glue new mirrorglasses in
Got today the cable for the radio antenna. The cable is with 20 cm around 5 cm to short for installation on our radio position
So we can finish the radio next weekend.
First clean up the wiring at the steering column. We don't install the cover as we wait on the horn relais.
The speaker is now complete with the control lamp. We need to customize a cable with the correct connectors between cb radio and speaker to got it work
Going on with the registration plates of roadlicence for the civilian trailer hitch which we removed for rebuild
Also add the registration plate of the truck
Without this no roadregistration in Germany possible
The shipping data plate is not mandatory for roadregistration but it is necessary to have a high score in the oldtimer appraisel
This is the old mirrorglass. We glue new mirrorglasses in
Got today the cable for the radio antenna. The cable is with 20 cm around 5 cm to short for installation on our radio position
So we can finish the radio next weekend.
Last edited:
- 494
- 1,043
- 93
- Location
- Germany
Thanks and Good evening
It is much more effort as expected but we like what we do.
Find out i can connect the cb radio complete on speaker and the handset. The original plug was available and i ordered immediately before it is out of stock. We will miss than the freehand function but i am sure i have on long trips always a codriver who can use the cb while i am driving
I ordered Ral 3009 oxidred spray for refreshing the plastic airvents. Seems match as best as possible the original "bordeau". We will test it before use on the original parts
- 494
- 1,043
- 93
- Location
- Germany
The weekend is "save"
Next goodies delivered
I have a lot of new relais in the shop but none fit. You use 3pin relais. We use here 4pin relais for the horn and it fit in different "connectors". So i need to order the correct one.
The cable for the handset which need to be customize with a plug for the cb radio instead the long one.
I am curious how the paint will come out
And finally the new screws for the cab in stainless steel black
I missed to notice that include the cabscrews set also all be which are visible. I will exchange all the blinky spots on dashboard, doorcover, sunvisors... i can't exchange all blinkys in the cab but the most
Next goodies delivered
I have a lot of new relais in the shop but none fit. You use 3pin relais. We use here 4pin relais for the horn and it fit in different "connectors". So i need to order the correct one.
The cable for the handset which need to be customize with a plug for the cb radio instead the long one.
I am curious how the paint will come out
And finally the new screws for the cab in stainless steel black
I missed to notice that include the cabscrews set also all be which are visible. I will exchange all the blinky spots on dashboard, doorcover, sunvisors... i can't exchange all blinkys in the cab but the most
Last edited:
- 494
- 1,043
- 93
- Location
- Germany
The mirrors come out perfect and the black screws look much better
I opened the cableplug for remove it
The day ended with detecting an electric failure. The horn have always power. I start on the steering column. All switches and connection work correct.
Next week i will continue follow the wiring to the horn to find the failure. I have no clue where, we call it "Kurzschluss" translator said short circuit could be located. There should nowhere be such issue. Well i will figure it out sooner or later .... in such projects be always unexpected things. Who don't want deal with this should not go in such projects.
I opened the cableplug for remove it
The day ended with detecting an electric failure. The horn have always power. I start on the steering column. All switches and connection work correct.
Next week i will continue follow the wiring to the horn to find the failure. I have no clue where, we call it "Kurzschluss" translator said short circuit could be located. There should nowhere be such issue. Well i will figure it out sooner or later ....
in such projects be always unexpected things. Who don't want deal with this should not go in such projects.
Last edited:
- 494
- 1,043
- 93
- Location
- Germany
The panels come out not exact matching but it is the best result. Next RAL Code is darker
We start measurement about the horn "problem" but couldn't solve it today. About other duties could we check today just two possible reasons. First the horn button at the steering column work like it should. The switch between Airhorn and stock horn is also correct wired. Still a lot of traps to check where the failure could be located.
We start measurement about the horn "problem" but couldn't solve it today. About other duties could we check today just two possible reasons. First the horn button at the steering column work like it should. The switch between Airhorn and stock horn is also correct wired. Still a lot of traps to check where the failure could be located.
Last edited:
- 494
- 1,043
- 93
- Location
- Germany
After checking every possible cable connection, I finally located the horn relay with a faulty diode. I had already suspected it, but since it was so difficult to access, I saved it for last.
After running out of time again yesterday, I've postponed the repair until next Thursday (Christian Holiday in Germany called Christie Himmelfahrt). I think I'll put a cable connector in between so I can rebuild the wiring in peace at the workbench.
Today i could continue at home in my office a little bit Soldering Work for the Military Speaker. The speaker hat a cold solder joint therefor he was thrown away
I use additonal a magnifying lamp, i hope it is the right translation. We call it Lupenlampe
My eyes are old-age so i need this for this very small and fine solder joints even though I have good progressive lenses
i felt like a micro-surgeon
From This
To This
Inside the Speaker is also a little bit Soldering Work necessary
After running out of time again yesterday, I've postponed the repair until next Thursday (Christian Holiday in Germany called Christie Himmelfahrt). I think I'll put a cable connector in between so I can rebuild the wiring in peace at the workbench.
Today i could continue at home in my office a little bit Soldering Work for the Military Speaker. The speaker hat a cold solder joint therefor he was thrown away
I use additonal a magnifying lamp, i hope it is the right translation. We call it Lupenlampe
My eyes are old-age so i need this for this very small and fine solder joints even though I have good progressive lenses
i felt like a micro-surgeon
From This
To This
Inside the Speaker is also a little bit Soldering Work necessary
- 494
- 1,043
- 93
- Location
- Germany
The horn is working nicely now
This small bad boy was the cause
it seems 45 years ago was the relais without a diode and this was added on the connection.
After i noticed the new relais have already the diode include was it just a cut off from this old bad boy of the past
Now where the horn is connected and working we decide to buy a new horn. Unless it work it sound like we drive a truck from the "Waltons".
For all Oldtimer Puries will we store that horn.
Unfortunately the airhorns are not allow in the city here in Germany so we need for roadlicence a "normal" horn.
So lets start to clean up the mess i have now again on the dashboard after measuring several connections...
This small bad boy was the cause
it seems 45 years ago was the relais without a diode and this was added on the connection.
After i noticed the new relais have already the diode include was it just a cut off from this old bad boy of the past
Now where the horn is connected and working we decide to buy a new horn. Unless it work it sound like we drive a truck from the "Waltons".
For all Oldtimer Puries will we store that horn.
Unfortunately the airhorns are not allow in the city here in Germany so we need for roadlicence a "normal" horn.
So lets start to clean up the mess i have now again on the dashboard after measuring several connections...
- 494
- 1,043
- 93
- Location
- Germany
During solve the mess under the dashboard occurs a new failure
The light switch is gone
Looks innocent but don't work anymore.
Available in Germany for 80 Euro or i import myselve 45 Euro all taxes and shipping include for an ACDelco Switch
The light switch is gone
Looks innocent but don't work anymore.
Available in Germany for 80 Euro or i import myselve 45 Euro all taxes and shipping include for an ACDelco Switch
- 494
- 1,043
- 93
- Location
- Germany
On wednesday we got the new switch.
After assembling we had a headlight Failure. No more headlights passengerside, no more highbeam both sides, Parklight avaiable both sides
I thought i got crazy. After control and measure the result was no failure inside the truck.... so we search between firewall and headlamps. What we found was so unbelieveable that we never thought about it.
Finally it was a partielly loosen headlampconnectors. They are new like the headlamps.
The rubbercover on the lamps give so much pressure on the connection that it slip off after a while. Left side was fallen off already.
Never seen such thing happen in more than 40 years of vehicle repair and maintenance
"You choose a fine time to leave me headlightconnector... "
After assembling we had a headlight Failure. No more headlights passengerside, no more highbeam both sides, Parklight avaiable both sides
I thought i got crazy. After control and measure the result was no failure inside the truck.... so we search between firewall and headlamps. What we found was so unbelieveable that we never thought about it.
Finally it was a partielly loosen headlampconnectors. They are new like the headlamps.
The rubbercover on the lamps give so much pressure on the connection that it slip off after a while. Left side was fallen off already.
Never seen such thing happen in more than 40 years of vehicle repair and maintenance
"You choose a fine time to leave me headlightconnector... "
- 494
- 1,043
- 93
- Location
- Germany
4 weeks ago we was already at this point and than the horn failure occur and had some minor other annoying problems with it.
Now all is solved - we really have now enough of electric mysteries...
The adaption of the mil speaker for the cb radio work well.
The dashboard speaker for the radio are ok for now but in future we want a better sound with additional speakers. We delay this and go on to preparing for roadworthy.
Now all is solved - we really have now enough of electric mysteries...
The adaption of the mil speaker for the cb radio work well.
The dashboard speaker for the radio are ok for now but in future we want a better sound with additional speakers. We delay this and go on to preparing for roadworthy.
- 494
- 1,043
- 93
- Location
- Germany
Continue to prepare the hood assembly.
This will be a difficult job by just 4 hands.
The vent to cowl assembly needed some customized pins as the original was gone
I found some used in the USA for sale but with import fee and tax not worth that money as its the same condition like ours. So i customized the pins ourself. Hopefully the plastic pins will last long enough of our live.
All prepared for hoodassembly tomorrow. I hope the the hood fit in easely without much adjustment....
Meanwhile we gave him his face back today
This will be a difficult job by just 4 hands.
The vent to cowl assembly needed some customized pins as the original was gone
I found some used in the USA for sale but with import fee and tax not worth that money as its the same condition like ours. So i customized the pins ourself. Hopefully the plastic pins will last long enough of our live.
All prepared for hoodassembly tomorrow. I hope the the hood fit in easely without much adjustment....
Meanwhile we gave him his face back today
Last edited:
- 494
- 1,043
- 93
- Location
- Germany
This small 2 to shop crane does always a good job for us
Could be more exactly adjusted but it's not possible between fenders, doors, front and cowl to vent....
Could be more exactly adjusted but it's not possible between fenders, doors, front and cowl to vent....
- 494
- 1,043
- 93
- Location
- Germany
It took a lot of hours specially the doors. These are aftermarket doors we bought 1995 after purchase. Original the truck had a lot of dents of his army time. So he got new doors, new fender and a new hood in 1995 before he was paint in red as business truck for our metalcompany. Nothing is more worse as to adjust these aftermarket stuff! But there was no chance to got off these dents from the original parts. Looks like someone use the truck as punching ball.
We start by mount the cab, the fender and front with little pre-adjustment. With the doors start the real adjustment and it took the most time. The hood was mount in 30 min but the adjustment took again 2 hours.
I am not satisfy with the result but its the best we could got.
Would you go another route by assembling the parts?