Search results

I want to install a quick connect coupler to the air line on the passenger side firewall on my deuce. I have attached some photos for reference. My plan is to attach the coupler (photo 2) to the thread on the fitting (photo 3). Any problems with this?

I have read numerous threads pertaining to steering gear leaks. One referenced TM9-2320-209-20-3-2 outling the steps to move the engine for gear bolt access. I have looked and the TM and could not find it. It may be there and I am educationally challenged but does anyone know what section...

I recently purchased a new 0-120 oil pressure gauge and sender unit. I am replacing 0-60 and there are two rubber connectors on the real housing; the one on the left is smooth and the one on the right has ribs. Problem is the new gauge has the riibs on the left and is smooth on the right. Do...

I would like to remove the gun ring mount from the passenger door frame. I plan install a metal plate as filler so I was wondering if anyone who has done this could post a few pictures. I would like to get an idea of how the door will look when finished. Thanks

When the frame seal is installed, does the convex side go toward the windshield frame or the front of the vehicle?

I was unable to find an answer to my question via search so here goes! I purchased the components for my remote brake reservoir from Wilwood Engineering. I would now like to see if I can make it compatible with my power bleeder. I checked with Wilwood and they do not have any type of cap to...

I have been searching for the past hour trying to find posts that could give me tips on installing the three sided windshield seal into the windshield glass frame. I have the new seals ready to go and hope someone can tell me the best way to do it

I am trying to source two seals which go on the windshield hinge bracket. It is P/N 8741839 shown as #22 in the attached illustration. Any ideas if and where these can be located? Thanks,

Does anyone know where I can download a free copy of TM 11-5830-340-12?

I received my VIC-1 intercom system today and would like to download TM 11-5820-401-10-2. Anyone know where I can download this for free?

I am trying to clean up my data plates and remount them on a freshly painted dash. They were fastened to the dash by some ugly screws and was thinking about re-fastening them with pop rivets instead. Any suggestions?

:?: I am starting on the refurb of my driver seat and want to take it apart, blast it and repaint it. I am doing my interior in Rapco Semi-Gloss Olive Drab. In looking at the construction and springs, it seems like it could be a real nightmare trying to get it back together once the parts are...

Anyone know of a source for reasonably priced camo cargo covers for the M35A2?

I removed my radiator today to replace broken pop rivets that hold the shroud in place. I flushed the radiator and engine block which was surprisingly clean. My original plan was to replace the hoses and belts while the radiator is off but the currentl belts and hoses look almost as new as the...

I purchased a 24V BatteryMinder with temperature sensor. I had a few questions about installation and tried to call their Customer Service line but kept getting recordings. I finally emailed them and received a response a few days later. I replied to their email asking for some clarification...

I have started on the interior aspect of bobbing my Deuce. I am doing the exterior in Rapco 383 Green (Camo) but I will do Rapco Olive Drab Semi-Gloss for the interior since I like the finish better. I started with the companion seat. Blasted the frame and ordered a set of canvas seat covers...

Time to address the cargo seats on my Deuce bobb project. The wood was in very poor condition but the fact that I could cut off one 36 section made my repair options. I started by removing all the slats. This in itself was no small job since the nuts were near impossible to get off with...

I am in the process of bobbing my deuce and am refinishing each part as I get to it. As far as the front fenders are concerned, are there any recommendations as to how to handle the non-skid area between the two ribs on the front fenders?

I am about to reassemble my 10K front winch. I have installed all new gaskets and seals and everything is cleaned up and painted. Unfortunately, I have slept some since I took it apart and have a few questions. The TM list the assembly steps but I am unclear on two items. First, can you...

I am trying to find information on the correct method to install a new cable on the front winch. TM's do not seem to address this for the front winch and a search has come up short as well. Any help is appreciated.