Search results

Does the med duty tow bar work on the front mutt tie down fittings? Thanks

2nd Annual Copper County Military Encampment From 12 Nov-20 Nov in the Copper County State Forest Main camp is at 46deg 10' 70" lat, 87deg 51' 00" long (This will get ya close) Main camp is open to SDDC club members only, nonclub members are welcome to stop by for a cup of joe. All non MV's...

While troubleshooting the personel heater in the van body of my M185, I found the fuel igniter was baked ( picture a car cigarette lighter with something burnt on 1/4 of the coils ) I believe the heater is a Stewart Warner 30,000 btu mulitfuel 10530b heater. Would anyone know if parts are still...

Does anyone have the "pin out" diagram for the female trailer harness? (it would be the one on the truck that the trailer plugs into.) I hate to get out a multi meter and check myself but I will be towing a cucv and need to come up with tail lights. Thanks ~ Pappa-G :lol:

Whats a set of six 11rx20 michilins on duce rims worth?

Ok now I know youre thinking this should be in the "electrical" section but thats under restorations and this is a modification question. I pulled the black out drive light apart and replaced the tiny bulb with a 28volt 250 watt aircraft landing light bulb. It looked good so i made anotherone...

Hey guys, I need the comercial ( national ect.) seal number for the front output and rear output seal on an air shift transfer case. Thanks ~ Pappa-G

Do you need a lift for 33's? or can ya just trim the fenders on a Blazer?

Whats the difference? Other than one is every where and one is unavailable? My trans/transfer is producing a whine in high 4-5th gears but not in low range ( leads me to believe its a TC problem) I should have never put a muffler on!! :banghead: :banghead: :banghead: :banghead...

I have just painted my Duce and I would like to have the correct markings on the truck. Does any one know the best way to do this? ( paint / decals ) I have a flat finish paint will the decals work? Can you get the decals in a flat finish? Thanks ~ Pappa-G :confused:

I could have called this "rear studs" but it didnt sound politically correct. When running just one tire on the back axels do you need to use something other than the stud/nut or would you get more front wheel nuts and use them?? Help me I'm being oppressed~ Pappa-G :confused:

:confused: Does any one run on the Mich. 11Rx20 XL tires?? I often see them in the larger sizes. Thanks ~ Pappa-G

Is the wiper travel adjustable? The pass side sweeps the complete window while the driver side is a short stroke. Am I ate up with the dumbasse or what? :banghead: :banghead: :banghead: :banghead: :banghead: :banghead: :confused: ~ Pappa-G

:confused: I've been searching for a couple of days now but I cant seem to find it. Does anyone know the TM# that covers split rims?? :confused: Thanks ~ Pappa-G

All this talk about "Super Singles" if I switch when I switch from 9.00x20 to an 11.00Rx20, will I need new innertubes or will the old ones work? :yeah: :shakehead: And if I need new where are they available? Thanks ~ Pappa-G

:confused: I have seen A few listed at DRMO but they carried an additional identifier (though I cant remember what it is an "E" or "X") I had heard to stay away from them due to there limited production. You know the story : "A better idea that wasn't." :idea: Has any one else made one or...

While in my thinking room the other day I came up with the idea of giving my M185 a pass through cab. Narrow the passenger seat and brake out the saws-all :freaked: Has any one done this to thier M185, M109 and so forth? Just picture it the super sleeper from H%$L Let me know what you think...

I just received a "CP-3050 Benmar Multifuel Heater" and it came with everything but the installation guide. If anyone would have a TM, FM or instructions of any sort I would appretiate it. The -10 only tells how to start the heater but there is nothing on installation. I guess I could allways...

I'll be making an 850 mile round trip in my M185 over the next week. <img src="emoticons/icon_smile_jawdrop.gif" alt="Jawdrop"> Is there anything "special" that I should do to prep the truck?

to remove the crank I've gor to remove the frnt plate. To remove the frnt plate I've got to remove the cam gear. The cam gear only has two holes for cam retainer access bolts. there is also no cam gear retainer bolt. Am I missing something??? <img src="emoticons/icon_smile_help.gif"...