Search results

Did you check? and made sure that the WARN preminum hubs are for the stock CUCV Dana 60, 30 spline outher shaft and not the after market 35.

Ditto "ida34". Tighten the P/S belt first, there are 3 bolts securing the pump, the #1 alternator (driver) #2 alternator (passenger) can be done at any time

On civilian truck/SUV, vent windows are different (73-84) & (85-91) The 85 ON assembly can be used as a replacement for 73-84, There may be a difference in the placement and number of holes . The 1984 CUCV, have NONE tinted glass, the two pieces weather strip molding and the black locking...

First, Sorry about my spelling. What I am sayng is that a lot of people dissmise the use of spacers, but spacers when properly made have found uses among heavy rigs and are DOT approved (DEPARTMENT OF TRANSPOTATION) even for some big rigs application. They are not and answer to all, but a...

the Humvee wheels have connical lugs holes and nuts and can not safelly be used reverse for high sustain speeds, they may not even center correctlly as the CUCV are not hubcentric, some of the Civilian early H1 Hummers "The scout" among then had the single 1 piece steel wheels and were hub...

The CrossOver stering is a "SHOULD" do upgade kind of a thing. I consider it a nessecity with the 1973-1987(1991) GM trucks Any time you off road a lot or go to wider 35" or taller tires. The added weight inertia & friction from the taller/wider and heavier tires/wheels puts a lot of strain on...

Cost for a "79-"87 Ignition & door OEM Keyed alike locks set part # 1171892 $27.00 + 7.00 S/H. I did not shop around but they arived with in 3 days from GMCPaul's Truck Part's in In. (765)344-2906 Online Catalog: GMCPauls Truck Parts as of 10/07/'05 door locks are very easey but brite finish...

dsstang97 I would buy the used one for a $100, if you know is working and up to specs. Then if and when is dead you can rebuilt it. Not 100% sure of the part numbers but, there was an early and the more dissarable later model. Good luck either way!

With all the possible ways to lift this trucks and give articulation... My money for "OFF The Shelf springs" is on "BDS". I used their 5.5" spring lift for a 3/4 ton truck, that net me the 6" I was after with the Dana60. They are narrower then the 3" wide OEM springs used in front, but have more...

Lance "Thank You" I could not find the "thank you" key?? I have wonder about this for a while. I have an electric Ramsey 12K. Patriot that I would like to used in another vehicle. And install a 12K-15K capasity winch on the M1008. Not sure about hydrolic with its constant duty advantages or...

The only place I know of is Ebay now our days, Keep an eye in the classified section of SS, I have seen a couple over the years. I Got 2 from DP military supplys(?) 5-6 years back there are several vertions and volts (two 24v. versions widely use by the US MIL. forces) = 30amp. 1/2 drive pistol...

Or for the Robo-impact tool 24v. torque wrench, you can change/dismount your tires and eveyone elses for that matter as long as your truck is up and running, I have wonder if this would be a good temp. 24v. source for a removavle 24v. winch. Any Idea???

Whent thrue this with my #8 cylinder broken off GP tip, I used a surgical type swissers, my short 45* needle nose did not allow axcess into the chamber . Read a tread in another site were fleet mechanics, routingly break the tips off and tap on it with a small chissel so that the curvature of...

Thanks AJMBLAZER. I did not think of that. I had seal or known chevy cab leaks, replaced door & window seals (the vent windows are a PITA) and wheater stripps, added the artic insulation undermatt and replace the HD rubber matt. That made a "HUGE" difference, untill I opened the Air cleaner...

Most rigs using levers or valves, that I have seen are some where in the floor middle or to the drivers left for eassy acces. You could place it on the dash, like bottons on Big Rigs maybe one the plates that many M1009 have in the dash trim and reinforse it from the back with bolts & a metal...

You can get replasments at the auto parts store for $100-140 using the OEM #1105500, but you most tell then that it has an Isolated ground and for an ambulance or limo aplication to get the 100 amp model, otherwise it will most likely be a 70-75 amp unit either way it may not last with their...

Hello Glen. Your "on the road" 20 MPG or more for a M1008, N/A 6.2 and the stout but power sapping 3 speed TH400 and 4.56 gears is Very Good and unusual. Most SS members seem to average 11-14. Not sure of their driving, terrain and modifications. For the M1008, I ended with after the build...

Kudos to you and companion on your journeys! Glad to read that you average 19 MPG. I did as well a couple times during long trips a few years back, when largelly stock with the OEM A/T tires. Now with crappy Diesel even with additives, a few hundred extra pounds (and less aerodinamic) Add-on's...

A metal cigarette lighter dilitte plug. And is also a potecial 12v. source to you!

Hey spink7124, I had send you an email a few weeks back about details on your build, Thanks for the reply. You have Great articulation with some straight forwards parts. With your capabilities, steering is Xtrmly Important. Look at LEE PERFORMANCE STEERING, in Ca. before dessiding what to...