Search results

Whats the dot5 for?

On my recovery from Ft Bliss(800 miles) I got 7 to almost 8 MPG. Good luck be safe.

Can you tell me where the module is located. On My recovery trip from El Paso the fuel solenoid on my M923 shorted and burned the wire all the way back to the run/start switch. We unplugged the wire(54) by the switch. Since then I have no low air and no park brake light or buzzer. Looking at the...

Is this part your talking about. Integrated Parts Systems - Selenoid, Valve 24v, 250 Cummins If so one wire goes to the run/start switch the other to a diagnostic connector. If yours stays running there is a thumb screw on the solenoid to manually open it. Maybe its screwed in. If you unscrew it...

What the time frame to get back your SF-97? Do they send title to Texas residents? For my 5 ton.

395s are 53" tall?

I used a piece of 1/4" flat brass about 10" that had i little bend in it about 3" from one end. Just tapped them off. The chisel idea sounds like a good one thou. I ordered mine for Clarks. They had very sharp and rough edge. I worked on each one about 5 minutes with some fine sand paper. I...

Transfer case info here. http://www.steelsoldiers.com/5-ton-up/79779-m939-series-transfer-case-low-range-front-axle-engagement.html

A BIG Thank You to jpekarek for taking the time to document it all. I've done hubs on My GMC Topkick before but its always good to see some pics so you know what your getting into. The hubs on a M923 must be a lot bigger because there is no way you could pick them to put back on the axle. Now...

I don't know about front seals but I'm sure they have them. I ordered all the stuff for the rears on my M923 from Clark. Rear seals are on sale right now. Price was $19.00 per hub(2 seals). Integrated Parts Systems -

How much per mile was shipping?

f. Transfer Case Control System Operation. The transfer case control system converts four-wheel driving power into six-wheel driving power, provides smooth shifting of transfer case into high or low driving rangs while vehicle is in motion, prevents transfer case from being shifted with...

Thats good to hear. I need to put a mechanical gauge on my M923 with the 250 Cummins. It reads about the same as yours. I hope its just a sending unit or gauge.

Ok here's a few pics. First 3 on in Ft Bliss GL lot. #4 stop for the night in Ft Stockton. #5 Fuel and lunch in Ozona. #6&7 previous operators. #8&9 some goodies in the truck there was also a bottle jack and the operating manual. #10 little hill at my buddies place(where going to have to find...

Any pointers? I didn't find anything in the TMs. I do have a axle that started leaking about 160 miles from home and the opposite side same axle that had a streak of oil running down the tire while sitting on the GL lot but didn't leak while driving. Light was on when we left El Paso. Ordered...

I live about as far south in Texas as you can get. Edinburg. Just recovered my first MV 12/28 M923.

Picked up 2 M923s from Ft Bilss 12/28. First video is sitting in Ft Stockton 12/29 getting ready to hit the road. My Buddies truck didn't want to start. Figured out later the tank vent was plugged. So we determined that when the fuel cooled over night it pulled all the fuel back into the tank...

Mine has the same problem. Ill post what I find.

Greetings from Deep South Texas(Edinburg). Just recovered my M923 from Ft Bliss 12/29/11. That is one long drive.

fsearls92 Thanks for the info on my buddies truck. Had a bypass line ready to temporally bypass the drier. Do you shift into low while in gear or do you pop it into neutral? Ill post the epic recovery later. 590 miles in one day