Search results

Something doesn't look right. I don't recall the big "C" bracket that far forward? This shouldn't be that wack. Next question...where did one get the mirror? Snap a picture of the windshield brackets. Does mirror have a label, "Trash cans may be closer that they look" CAMO

What a bunch of BS is all I got to say. The last sentence should make owners feel good about governmental control. " The DMV apologizes for any inconvenience." What a way to start the day. CAMO

That part is a circuit breaker. Don't normally see a breaker in that circuit. Trace it out.... Always something new, CAMO

A little footnote to computer's, microprocessor's, rom's & prom's when handling. Follow proper ESD procedures. Electro Static Discharge. The little static spark one doesn't see or feel and POOF... Time for more parts., now or later when they fail. 🎆 Nice video. Sparky the electron just...

Dog Says "Hurry up and fix this thing. Wanta go for a ride" WOOF woof, CAMO

Ran into that also. Another HumV "What were they thinking moment" Couple of pictures to tell the story. Plasma torch and wire guide. Cut and clean up. the problem the guide the cut the clean up paint to hide The pesky hang nail. 50,000 degrees and done Goggles on and press the button, CAMO

First off... Camoteksystems is not a game. Second, cause and effect of cascading components is more than likely as stated above. One can see that the HEXFETS are toasted in the picture. ? is that the controller? Third, the resistor in question is an 100 ohm, 5 %, 1/2 watt. Fourth, basically a...

Splice one of these in and get back to swish swish swish, CAMO AND some of these CAMO

Yes, It can / does happen. Riding around in a HumV has its own fun factor. (y) Mine is in great running shape, trusting it to go anywhere. Funny part, likely do the same time riding around on a mechanics creeper... checking this and that LOL. It is a education from the bottom up of the...

This might help. http://www.ltw.net/Hummer/manual2.pdf Get the LO down on Lube Orders, CAMO

I slapped them on the tie rods ends. Looking like they could have been a bit wider against the knuckle side... BUT tried one all buttoned up...Smushed tight and sealed good enough for Mr. HumV. Going on 8 years and no cracking, leaking, dirt/dust intrusion... Better than NEW. Red ones get...

You got one hell of a good fuel pump. Now YA going to put the air compressor to it and maybe pop it back out. Damm that sucks, CAMO

YES to all of that and more. (y) My post is to simply show what can be going on in the tank. Thinking it thru to the whole fuel delivery system. One would not want crap (maybe beer) flowing thru one blood system... so just pointing out what can be lurking in the tank and shut down that NU to...

From gears to pickle's... I thought there was a lot of great information shared. Once and a while the guys in the shop will hide a lunch pail or toss a wrench🛠. OK, which one of you monkeys ate all the pickles. 🐵🙈🙉🙊 Just another day on the internet shop floor, CAMO Back at the motorpool...

Got your attention ? I don't usually link to UTUBE but this is a good one IMO. Diesel fuel and it's issues. Just another thing to consider when doing a precheck on that new to you old HumV. Watch on two time speeds. Who works that fast ....lol Tiger in the tank, CAMO

Tomato....Tomahto. In a salad or on a sandwich, All tastes the same. Extra pickles please, CAMO

Metal or plastic... Both are going to be expensive. Check with BULLDOGGER. He has skills to make such canvas craft in the past Could be opportunity here $$$ Rock, paper, scissors... CAMO

Change them all. Front and rear. Radius rods 4, tie rods 4, pitman 1, idler 1...ran out of fingers. Extra ?? New chew toy for Diggy, CAMO

Voice from the back of the club house... It's a HumV not a bathtub or submarine. First thing I did ...cleaned all that crap off for a visual and clean electrical bare connections, Through OUT the HumV. That never been done before? Something I can see and work with. Under the glopped on...

Here's a tip to the flasher. See the attached drawing, to eliminate the flasher unit.⚡ Connect a jumper between the two pins "A" to "B" flasher connector cable. ( a 3 inch piece of solid 12 ga insulated wire with 5/8 bare ends, think romex) This will provide continuous power to allow...