Search results

My tranny was shifting hard at High rpms... I replaced the hoses that were broken now the transmission seems like it shifts softer at lower rpms.... Is that good?

I have no Pintal so thats where it is.

I went to Home depot and boughyt the 1/4 tap and screw. I tapped the hole and put lock tight on the screw. Oh and I took off the fuel line and got my air compressor hose and blew out the port so that I didnt get metal shavings in my injectors. Then I bled and sarted it... So far so good, Now...

I am going to do the 1/4 tap and plug method as a temp fix.

Good news is..... It is not sucking in air into the system. Bad news is ...I now have a drip in the back of my filter.

:idea:I took the O ring out and it was cracked up. I took it to Autozone, O Reilys, the Chevrolet dealer and nobody could match it. So I drove to a Hydrolic repair shop and the guy matched it and gave me one for free. So first I put it in wrong and fuel was leaking bad. Then I put it around...

can I take apart the pressure sensor and put a new O ring in it?

I have a 4ft X 8ft sheet of aluminum. Could I use that to fix my rotting floors?

kennyw your such a party pooper.... Yes I am going to weld the sheet metal... This forum is for quick fixes. I think the 2X4 is a pretty clever Idea. I hammered it in and it locked the seat in place. No more wiggling.

Seems like we all run into the same problems with our vehicles. Here is something I came up with to keep my girlfriend from falling through the floor. "The Ol' 2X4 under the seat trick". I posted these pics in another thread and I thought I would see if any of you guys had some fixes for my...

clearer stuff

Pictures of my dot 5 dot 3 mix The clearer jar is from the smaller reservoir /the dark is from the front res... it looks like an emulsion, and the 3 and 5 are separated. Which one is the heavier liquid?

I use my truck for fun and I do some daily driving with it. I drive 70-80mph on the highway with no problems. I haul a (2000lb empty )16ft dual axle utility trailer with brakes.... I love it. I drive at 80mph to my hunting spot, with my wet dirty dogs, lock in the hubs put it in 4 wheel low...

My passenger seat was going through the floor. I used the Ol... "2X4 under the seat trick... Did you guys know this fix? Its like the seat bracket was designed to fit a 2X4 ... fits perfect and is holding up my seat.

In the center of the STE fuel pressure switch there is a black rubber plug. Looks like a pool cue tip. Is that what leaks?

(I cut and pasted this from another forum I posted in) I just went to Radio Shack. I showed the guy the picture of ^ that green resistor(from a different forum) and they didn't have one that big. They had no 300 Ohm resistors. What they did have was a 5 pack or 150 Ohm 1/2 watt resistors for 99...

I am reposting this from another thread... RE: resistor fix. I just went to Radio Shack. I showed the guy the picture of ^ that green resistor and they didn't have one that big. They had no 300 Ohm resistors. What they did have was a 5 pack or 150 Ohm 1/2 watt resistors for 99 cents. Well I...

I am reposting this on the Resistor fix: :idea:I just went to Radio Shack. I showed the guy the picture of ^ that green resistor and they didn't have one that big. They had no 300 Ohm resistors. What they did have was a 5 pack or 150 Ohm 1/2 watt resistors for 99 cents. Well I figured I could...

I just went to Radio Shack. I showed the guy the picture of ^ that green resistor and they didn't have one that big. They had no 300 Ohm resistors. What they did have was a 5 pack or 150 Ohm 1/2 watt resistors for 99 cents. :idea: Well I figured I could waste 99cents on an experiment. I...

My 1009 does the same thing. Starts for a few seconds, then runs out of fuel because there is air in the system. I open the hood and open the bleeder valve on my fuel filter. start it for a few second, and it bleeds the air out of the filter, then I shut the valve after some fuel has bled out...