Search results

Does anyone know the part number and name of item 38 in the below picture?

All- Im looking to fab a "ballistic" wall for my M1114 (mainly to hang the rear A/C unit and cannot find a good drawing or sketch or even how it's installed and the unit mounted. Any help?

I was asked to run "tail gunner" during an escorted fundraiser. Truck ran great and lots of money was raised.

So @fuzzytoaster and I were chit-chatting a while back and he asked how the M715 was going and I told him I was just about done with her and I said "Yeah, I don't know what I'm going to do to keep busy now.... I still have the fever.." He says: "Well, there's only one cure for the fever...."...

Sent a PM today and this was the time stamp... I didn't know time travel was possible on SS.... BEST. SITE. EVAR!!!

All- I need this piece that goes between the doors and top. A link would be great or the name of it so I can find it.

I truly do love this truck!

She stepped up and stepped out! Met some friends. Took some glamor shots... And had a great time hanging out! All in all a pretty awesome day! She's burning a little oil, so a ring job is next.....

All- My horn worked intermittently, then quit altogether. Today I took some time and started troubleshooting. Removed the horn, connected it directly to the batteries, it worked fine. Checked to see if I was getting a good ground at the horn via the wiring harness and I wasn't. Going on...

My horn has quit working and I know the issue is in the "ring" on my steering wheel. My issue is I'm scared to death to pull the horn button off without some kind of direction as I know I'll end up breaking it beyond repair. Does anyone have either directions for fixing the ground or can...

So glad to have her on the road again! And my buddy got some shots while we were leaving.

Ok gents- I've tried and tried, but I cannot seem to get the sag out of my driver's door. I've adjusted the hinges (I have found they move them in and out) The doors themselves And in the process got the gap too tight (Note the chipped paint) I cannot seem to get the gap correct and...

Ok all- Here's where I am: I rebuilt the T230 Tornado, no oil pressure on the electric oil pressure gauge, so I put a manual testing gauge on and still no pressure. I pulled the oil pump and made sure it's primed, still no pressure on the gauge. I pulled the quick disconnect off of the...

Pretty stoked about it to be honest!

Ok all- going to be changing an oil pump when I get in. Looking at the TM it seems pretty cut and dry- remove the 3 retaining nuts, pull it out, replace the gasket and reseat the new one. Any heads up or words of wisdom?

All, Not to knock the MVPA, as their focus is on restoring our vehicles to "issued" status. My vehicles are anything but..... Is there a MVCC located in our area? If not, how much interest would there be? Mainly Louisiana specific at this time, but I think it would be a great way for...

@Soupermike invited me to a car show in New Roads, LA, and this being my last weekend home, I was eagerly looking forward to it. Friday night, Bertha was fueled and loaded and ready to go: Jak and I hit the road early, and as usual, he was on point with his navigation skills: We got...

Guys- I had the issue where my Purge valve was sticking open. Followed some advice and lubed it to no avail. It turns out the O-ring inside had disintegrated, so I had to rebuild. No one was able to find the TM section for rebuilding the Purge valve on the dryer, so I figured I'd be the lab...

Ok all, My pop off valve (when you build pressure it pops off) is sticking in the half open position after I build air, bleeding it slowly down. I had this issue once before and for a temporary fix I followed the advice of @fuzzytoaster and used an extension and hammer to whack it back into...

When I first put the soft top on my M715, I thought "Lord, that frame bow hill is the ugliest thing I've ever seen!" I was researching hard tops for it recently (just wandering across the web, no intent to change it any time soon" and came across the hard top offered by Boyce, and my first...