• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. rosco

    MEP-003A just goes click when trying to start - fully charged fresh batteries

    If the engine is not cranking, you have to determine why. Fundamentally, it needs to have current to the starter. Determine that. Disconnect & scrape clean, the other ends of all the battery cables, & electric connections. As stated, check that solenoid by jumping it with a screw driver.
  2. rosco

    Highway speed

    Those King Pins are in the "Real Tough" category. So is the 5th wheel. Probably when the king pin sheared, the trailer went forward, and a crossmember hooked and bent the 5th wheel. I always have the lights on & have added the required clearance & three bar markers to Medusa. Same on the...
  3. rosco

    Hitch Fabrication

    Here are a couple more pictures of my heavy car hauling trailer, that I meant to include. Because of the tall hitch post on it, I use the lower, add-on hitch, but with an longer shaft (about a foot long, is all it takes), on the pintle. About These are all common variations, and I want to be...
  4. rosco

    Hitch Fabrication

    Certainly there are many ways to skin a cat and a great deal of skill, time, & energy, as well as good ideas, have gone into these hitches. But too, I hate to see the utility of the stock hitch impaired because of "add ons". And certainly, for pulling civilian & smaller trailers, there is a...
  5. rosco

    2740lbs in an M101A2

    I hauled a load down to Washington, about the same weight. The tire didn't like it much. I took the picture, after replacing the tire. I thought the spring would fail, but it didn't. In fact I regained its original shape, and is still in service.
  6. rosco

    Hitch Fabrication

    You won't be able to use the top hitch with some trailers. The new one is too close below & to the sides, when the trailer swings, especially in off-road conditions.
  7. rosco

    MEP Blues

    Unit 2: does it generate the other voltages? If it does, I'd start with the switch, and work back.
  8. rosco

    My 1954 M211

    Sharp truck. Its going to blend right in with the neighborhood.
  9. rosco

    Who has an M796A1 Bolster Trailer?

    I guess that a lot of us have them. Sometimes they are very handy.
  10. rosco

    M101A2 Brake Lockout Hole

    I suspect that the slight misalignment is wear on the fibre bushings/parallel side bars, that the pintle ring swings on. There are 8 of them.
  11. rosco

    m923 DRAGING BRAKE PROBLEM

    Granted Trailboss, but check, and re-check, and when you stop, you don't even need to get out (sometimes). The truck should roll/coast/rock, to ever so fine a stop. That truck shop won't be cheap!
  12. rosco

    m923 DRAGING BRAKE PROBLEM

    It makes me uneasy, hearing about all the Folks driving heavy trucks, and not having a clue about how they work. Probably a simple adjustment/check during the walk around, at the pick-up point would been sufficient. A CDL requires at least an elementary knowledge of the safety systems.
  13. rosco

    No Title for Truck - What Am I missing?

    Its probably late now, but try to offer to pay for the SF97 and do all the leg work, to get it transferred. Smarter next time.....
  14. rosco

    54 xm-211

    The truck looks great. Its something that you can get your teeth into. Pull the valve cover and crank it over -- see if the rocker arms & rotor are moving (worst case problem). Some of those 302 engines used a fibre timing gear (others used an aluminum one). Mine stripped a few teeth and I...
  15. rosco

    MEP-002A hz dropping under load

    Sometimes, cross referenced filters, don't have the proper gaskets with them. There is plenty written about this.
  16. rosco

    Quick M35A2 Starter Relay Question

    M-35tom: Right on! Thanks for the tip!
  17. rosco

    Fuel tank leak

    Locate the pin hole, and solder it. I once had an M43 with a tank full of pin holes. I took it out, steamed it good, turned it upside down & put a dollup of solder on each hole and its still running today (30 years later). There is no quick fix. It takes time and patience, but the repair is...
  18. rosco

    winch installs

    With your concern, and a couple of snatch blocks, you'll be able to handle about anything you come across!
  19. rosco

    M35a2 injector return line fittings

    Ah yes...... something else I should do. At least it is on top, instead of on the bottom of the truck. Thanks for the reminder.
  20. rosco

    Timing Marks -0- on Crankshaft and Camshaft Gears

    It seems like it could be timed 180* off. Then you use #6, instead of #1. Another common error, is that one mistakes the rotation of the distributer, thinking it rotates the other way around, and the wires to the plugs are on backwards.
Top