Search results

Is there any intrest in these doors. I can get blanks with the tool access and doors that open. $150 for the pair + ride if there is any intrest.

Well it is a stud but only half a stud. I am looking for ideas on the best way to get it out. Should have used the heat wrench on the nut like I had planed.

I have a parts truck with a D turbo and a good truck with a C turbo. I don't like the C (way too much whine for me) and want to swap the D onto it. What is needed to make the swap? Gaskets, time, etc. Might even drill and tap for a pyro when off.

I think I am getting fuel into the oil. I know that fuel can get in if the FDC is leaking but what if the flame heater is leaking. I have so much WMO and ATF in my fuel it is hard to tell by smell but it looks and feels thin and pressure is a little above 15 psi. I also noticed fuel dripping...

Question on packing the knuckle joints? On the older style ball knuckle joints I see the need to pack them in grease but on the new “U” joint style is there really a need to pack them in grease. I can’t see the grease getting into the “U” joint from being packed. The grease might help keep the...

Is there some type of reoccurring problem with the intake on the 6.2’s. I went by my source and picked up a M1009 but the intake and injector pump have been removed. He had 4 other trucks and they were all the same, intake removed and sitting on top of the motor. 2 had the injector pumps on...

Can someone post a picture of which wire on the 6.2 injector pump (blazer)needs to be hot for it to run? Other than the injector pump wire is there anythin else on the 6.2 that needs to be hot for it to run? I am going to look at a couple trucks and I know they don't have keys and I need to jump...

What is involved in changing the motor in a M108 from a gasser to a multifuel? Are they a direct swap?

OK I have 3 trucks and all 3 turbo are different. What turbo are these. With my hearing I can’t heat them spooling. I noticed the front blower is different. The turbo exhaust is also different.

I have a Heart sinewave HF24-2500XC inverter. 80-2512-24 The overload light is on when I connect the power and there is no AC output power. Any ideas on what could be wrong with it?

What radio / intercom system is this for?

Will new injector lines fix this leak or is something else wrong? I have never done injectoe pumps or lines before.

I got my new / almost new top, thanks Builder77. I got it on my new truck. I have the metal uprights and bows that are about 13" taller than a deuce. I cut 3 " off each upright. The top looks good. I might need to add some pipe or flat stock to help mount the top in the stock location of...

What are the run flats made out of? Aluminum or Magnesium?

I have taller bows on my truck. Thebows are about 13" taller at the center than regular deuce bows. Will a FMTV 12' cover work? I think the FMTV covers are taller than the deuce, am I right?.

I scored 2 amber and 1 red LED lights. One of the amber has the park light blown but works otherwise. I tried it on the deuce and it would not flash. It did come on very faint. I unplugged the rear light and I could not see it on at all.

What is the going price for a Gama Goat project? Ran 2 years ago, had to be pull started due to starter problems, ETC.....

The air show is this weekend. Barrman is bring his M715. I might be taking my M725, M35a2c, M35a2 if they want them. It is going to be a Vietnam War reenactment this year. http://www.centraltexasairshow.com/site/Default.aspx?base

Is it better to just replace the fuel pump or rebuild it. The one on my mew truck is not pumping. 24V in, fuse good, ground good but pump not running. I pulled it out and sis not see how to take it apart otherthan drilling some rivits out. Saturn has kits for $10 I can get a used one for...

On I just got this truck today. Went for the test drive. Most went well except for the air compressor getting hot, very hot. If was hot enough to melt the fuel return line. I noticed new red silicone on the bottom so I am assuming there has been some problems. Any idea what is wrong. It...