Search results

Yep as a tandem to much stress locked and running on anything that is not forgiving mud /snow. As a single believe at highway speeds you are going to get the unit to heat up way to hot. That plow /sander truck when in use would see slow speeds. When I plowed and sanded for the state I don't...

It will need full time air to stay in gaged and a switch that relieves the pressure when off. Still believe it's not the best thing to run a diff lock at high speeds single or tandem set up.

If you look at when the diff lock is applied to the MTV it is when you put it in mode if I remember. Full power to all axles front/rear. When I have used the diff lock in any truck it was only to come out of something nasty. It was then switched off as soon as the truck has reached hard pan...

Not meaning to off track but my daydream would be Wet suit for the OP. Large john boat with cover and waver runner as it can operate in two foot of water. Seems like sometimes you see the outboards out there helping but there motors are up because of the depth of water. Seems like even with the...

How many?

Yea that primary can be tough. They say you should never spin the canister. Well that's what I do. I loosen the bolt just enough to get the canister to spin and I spin off the canister. Clean/replace check for correct hardware. Then to get it started for install I hold the bolt with my finger...

Never known G to come up with some ''EXCUSE'' about anything. Myself he has always help with numbers, info and great mechanical drawings without any attitude. Fortune cookie say man never let ego turn him into gashole.

Cattlerepairman I had a door that did the same thing bottom back bottom to low. I took some very thin washers and put them under the bottom hinge plate between the hinge plate and cab. Then I install the bolts and you might need a helper this time. You might get away with just loosen the bolts...

OP received the preform packing and rebuilt the air cylinder. No problems now.:beer:

https://www.steelsoldiers.com/showthread.php?168859-Loose-Flex-Plate-Bolts&highlight=torque+converter+bolts

Don't quoit me but. 3116 cat has a large square head plug on the passenger side of the bell housing facing the front of the engine bay.

I was going to use something under my trailer but painted the wood instead. How many square feet do you feel that bed liner kit would do?

Believe in the beginning there was a fiber washer in stead of and O ring. First goes the cotter pin in retaining bolt to stop first washer from going to the bottom of the canister. Next is the steel washer then the spring then another steel washer then a fiber washer that fit tight on the shaft...

A spring to pull the emergency shut down back to the run position when you push the shut down cable back in.

I googled NAPA #5070 and if I remember that is the correct gasket but it did not show up. Maybe call NAPA and see if it is still a good listing for just the correct gasket. it's good to have extra. Don't worry about the mistake people have been trying to using the wrong gasket and trying to...

Yea the correct gaskets go in with one finger and no stretching. I forget the correct NAPA number but you have to order them alone or buy filter with correct gasket. If you have trouble ordering the correct or finding them PM me and I believe I have extra and will ship them to you free.

Ron you know that is light hydraulic oil not bud light right.

https://www.walmart.com/ip/Greenpro-Temperature-Gun-Non-Contact-Infrared-Thermometer-Black-Yellow/121562206?wmlspartner=wmtlabs&adid=22222222222062511638&wmlspartner=wmtlabs&wl0=e&wl1=o&wl2=c&wl3=10394516002&wl4=pla-4578228992928827&wl5=&wl6=&wl7=&%20wl10=Walmart&wl12=121562206_0&wl14=ir%20heat%2...

Agreed check with IR been there with gage problem. If the gage is correct can I ask what are you doing when it shows running hot. In town traffic stop and go, off road or highway.

No IP removal just to take out the fuel control. Just hope by taking it out you can get it freed up with using solvents. Just be care full and don't do it in the dirt if you can help it. There is the small clip that holds the governor linkage to the fuel control. I use a good pair of needle nose...