Search results

Continued. Tank install: What do you guys figure my old tank is worth? I would imagine there's someone out there who has a mule but can't afford a $700 tank that would be willing to put some sweat equity into repairing an old tank to save some $$$. $100? Old tank:

I got my Mule from Maccus in 2008. http://www.steelsoldiers.com/showthread.php?21797-1800-miles-in-47-hrs-for-an-M274 When Maccus did the restoration, repro fuel tanks weren't available. And the tank, like pretty much all Mule fuel tanks, was dented. So Maccus made an outside cover to give...

3/4" socket Axle nut socket (3", 8 sided-OTC # 1907. Napa can cross.) Flat blade screwdriver or chisel to bend up axle nut socket washer tabs Big pair of pliers Hammer 1/2" and/or 3/4" ratchet or breaker bar Small adjustable crescent wrench Pickle fork (tie rod/ball joint separator to get the...

If you want to remove the drive flange, all you need is a 3/4" socket. If you want to pull the axle shafts, you'll need: 3/4" socket Axle nut socket (3", 8 sided-OTC # 1907. Napa can cross.) Flat blade screwdriver or chisel to bend up axle nut socket washer tabs Big pair of pliers Hammer 1/2"...

Go look at this thread. About the first 20 posts is all you need. It's a step by step breakdown of how the front end comes apart. http://www.steelsoldiers.com/showthread.php?8460-Front-axle-seals-and-boots-stepXstep When you pull the drive flange, all you'll see is the end of the axle shaft...

I'm near Athens. If something in the front end broke, I wouldn't want to pull the drive flanges, because the broken component will still be in the knuckle. If it were me, I'd get the front end up, pull the drum off, pull the backing plate and spindle off and get the axle shaft out. If you...

ditto If you can find a remanunfactured unit in the can or an NOS one, by all means that's the way to fly. You do run some risk with units like that, if they haven't been properly stored, they could have corrosion internally. It's just something to consider. I assume it's just a larger...

It's expensive compared to the Gillespie. In the standard automotive world, it's a very good price.

That is a cool truck. Is still a 427?

http://www.steelsoldiers.com/showthread.php?110705-M35a2-conversion-to-M35a3-dual-circuit-brake-system

Well, I understand completely-it's a he...ck of a lot of work to remove it, especially if the vehicle is functioning. I had hoped to find someone who had a truck that was taken apart, being parted out, etc., so as to inconvenience them and me as little as possible.

Sadly, the A3 bracket is waaaay different. So much so that one person on SS who used one to convert an A2 to dual circuit had to drill a new hole in his frame for the clutch pedal shaft to exit. The A3 bracket also does not have the provision for the PTO shifter. On the standard A2, the PTO...

bump

It took me a long time to recognize this, but people assess risk in two very different ways. Some people look at a situation and think "How likely is the bad outcome?". If there is a low likelihood of the bad outcome, they'll move forward. The other worldview is "If the unlikely event occurs...

This is exactly right. I struggle with this every year. Put it out really early and then the thread has 10K posts or let it wait a bit. Dates are Oct. 18-22, 2017. Rally Facebook page: https://www.facebook.com/GeorgiaMilitaryVehicleRally/

One, a 65+ year old harness is no good unless it's NOS Two, consider what options you want before ordering a new harness: perhaps you want dual taillights, perhaps you want turn signals, etc. You can have harnesses made with all of these upgrades already in them Three: This is just my...

Except when they're really old. My '67 A2 had what I assume is it's original harness. My truck was released earlier than the mid-2000's GL dump so it's been out of the service a long time and was probably one of the rougher trucks when it was released. The harness was just trash-all of the...

I've never opened an airpack that had what I would consider a good canister.

That does look good. Like the rear winch cover. The genset is a civvy mod. Looks like the wrecker floodlights are gone and some civvy spun aluminum ones in their place. ZiggyO has the right ones in the classifieds. Mirrors are either bridge truck or ten ton, can't remember

I think the 2-6K estimate is reasonable. I've sold 2 winch trucks in the last 12 months for $6500. Both totally serviced, new batteries, titles, etc. One was a little prettier than the other, the less pretty one had a cargo cover. I think what you're going to see now that the govt. is...