Search results

Is there any reason I cant use a Waterborne paint gun with standard solvent type paint?

I just replaced my front drivers side axle seal and want to thank Banshee365 for his excellent post on the subject and to add a tip if you cant get the tie rod off the knuckle use a two jaw puller put the center post on the top of the flex joints stud the arms on the knuckles arm and crank away.

Ok took the deuce out for a drive yesterday 5-6miles found one more problem I think the engine's starving for fuel I cant get up to 55mph with the throttle on the floor, I just replaced the primary fuel filter yesterday with a military surplus one, After I bled the filters I noticed that very...

what type of regulator does the 60amp alternator use?

well yesterday I wired up my front turn singles well I check the lights and there's the turn flasher the B.O marker but no top marker so I unplug the number 20 circuit no juice with the head lights on so I check the other side same thing well by now I'm getting angry and it's almost dark so I...

I need to know what thread the drain cock is on a multifuel primary fuel filter canister.

Do any of you electric gurus think I'll have any trouble running a 1amp reverse light of the BO drive circuit?

I'm trying to mount my west coast mirror set on the drivers side first but I cant tell on the installation sheet where some of the brackets go I.E the clip on the cowl do the brackets both go on top ? one on each side? one top one bottom? where they all come together in the middle (brackets from...

well in a odd twist of fate my folks saw what seems (after much picture comparisons) to be a convoy of Oshkosh Truck Corporation Bushmasters MRAP going east on the new york thruway. any thoughts on why they where driveling them? instead of trucking them on flat-beds.

*maniacal laughter* At long last, it moves! Be sure to check out our YouTube hotline, available at uncertain time in the future -- or the past, depending on your plane of existence. Because if some of you go backwards in time, try not to end up like Fry: being your own grandfather & all that...

as any one who grew up on a farm knows getting a new tractor is something to be shared check out our new CNH jx95 hi clear one thing I like it's a whistler turbo it's no deuce but it's nice.

here are some pictures of john's outstanding Deuce gun truck it's based on one that would have served in 1967 so it has a N/A motor and and single thickness plate sides.

AAAAAAAAHHHHHHHHHHHHHHHHHH well I bolted on the new pressure plate from Saturn surplus and guess what looks like the fingers are too low of the new one as well here's some pics will any one that can go out and have a look at the clutch on there deuce's you should be able to feel how low the...

I found something at my local hydraulic shop that might work very well for the heater ducts on MV's here's the one I thought would work best http://www.flexaust.com/content190.html but they have many different types so try looking around on the site maybe there's one I missed.

I need the specs or TM number that shows how to adjust the finger height on the 3 finger clutch for the M35A2.

well yesterday I went to change the oil in my T-case took me a while too find the drain and fill plug's but I did so get the drain pan set and and pull the plug and out comes maybe one quart of oil :shock: I'm thinking O crap the T-case is shot!! well I get on with the job flush the gunk out...

I just replaced the oil in my transmission I put in 8pts as per the fill Capacity I found and it only came up to a point one or two inch's short of the filler hole is this correct? and yes the amount I put in roughly matches what came out.

hey I need to know if I can mount my GMA cargo cover without the side racks? it looks to short to me but I'm not sure, Any info or pic's? guys of your mounted this way.

I want to undercoat the deuce with something a little harder then auto part store "rubberized undercoat" something harder and less likely to pick up rocks would be nice :grd: :lost:

just found out Selectro locking hub's are made by Milemarker http://www.milemarker.com/ they can be had for $405 a set.