Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.
I have an older M series 5 ton with an identification tag that says m series 5 ton without winch. However, I am looking to put one on. Can anyone tell me besides the winch itself, mounting brackets, and propeller shaft etc, from start to finish what are all the components that I will need to...
Does anyone have a spare FDC, Type B pump for the multi-fuel engine? My Fuel adjustment shaft has some damaged threads or damaged adjusting nuts on the threaded shaft. Also , I am looking for the Idle adjustment stem and nut. If anyone can help, as always, it would be greatly appreciated. Thanks.
Does anyone have specs for the LDS 465 1a injector pump? I am looking for the specs for the fuel screw and the droop screw. I know there must be reference somewere. For example fuel screw might be 1 1/2 turns out from being screwed all the way in. I know how to make the adjustments, I would just...
I am sure this one has been tossed around a lot. Does anyone have a mod for the turn signal/ marker lights to allow headlights and the marker lights to work together at the same time for night time driving? Not sure if this would cause a volt/ amp problem. Just at night coming head on with a...
Greetings all. Is there anyone who can post a picture of their rear end to display the more up to date mounting of their tail lights. My 5 ton is an M series and its a 1955 so the lights are just mounted underside the bed with cheesy mounting brackets. Just waiting for me to back up and catch...
Can anyone tell me a good technique on draining the coolant from my multi-fuel? I am not sure how many drains are on the block and perhaps anywere else. I found the obvious ones on the bottom of the radiator and on the left side of the block ( on the turbo side). But if there are others I cannot...
Does anyone know where I can obtain a fuel tank for a m54 5 ton? I would like to remove my tool box on the passenger side and install a second tank. Thanks.
Is there anyone who can tell me if I can use this gauge to measure manifold pressure in my multi fuel LDS 465 1A Engine? I need to adjust my I.P. for 2400rpm (18 to20 hg) and at the droop screw adjustment( 8 to 10 hg) at 1600 rpm.
Does anyone know where I can obtain some door components? I need the small guides at the front and rear of the door that guide the window glass. the front looks like a heavy weather strip but the rear is a guide all by itself. Shaped like a horseshoe to guide the window up and can be seen from...
Doea anyone know of a good muffler that can be put on the multifuel engine? One that doesnt restrict or even more important raise EGT's? I would like to quite her down just a little bit.
Does anyone know if there is a cross reference for the intake flame heater? I need to replace and didnt know if it was available from Wix , Baldwin, or any other. Thanks.
My 5 ton came with a engine coolant cab heater. The fan motor has finally given out. Can anyone tell me where I might find this small 12 volt bus heater motor? I have attached photo's of the bad motor. Any guidance would be great help. Thanks.
Does anyone know were one could find a trailer receiver ring take-off to buy? I have a 8 ton trailer but the ring is too small. Or maybe the 5 ton's is too big! I will not alter the truck so I would rather find a military ring for my trailer. Thanks.
Has anyone ever taken apart their booster pump which is located on the side of the multi-fuel injector pump. The line from the primary filter goes directly into the pump directly through a plunger assembly. I fear before I have owned the truck someone incorrectly put the assembly together. I...
My m54 5 ton has no fuel pressure between the secondary fuel filters. I am tapped into the bleeder port in that location, can hear fuel pump running, but no pressure. Can anyone help?
Does anyone know if there is a TM For my gas heater? It is a M68 model # VBM-250A. Cannot seem to find any info. Your help would be appreciated. Thankyou. The tm # is TM5-2805-208.
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!