• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. T

    M1008 Fuel lift pump need HELP

    I have it working now. With the fuel filter bleed open, I pressurized the tank until fuel filled the pump and came out of the filter bleed in a solid stream. Then closed the bleed and did the crank/bleed cycle 5 times until no more bubbles were coming out. Then I could start it. This was...
  2. T

    M1008 Fuel lift pump need HELP

    No, the fuel didnt gush out of the supply line. Some came out, then it stopped. I put a little air pressure on the fuel tank, and fuel comes out of the supply hose, but it stops as soon as I take the pressure off. The truck was running fine before all this, just had a fuel leak at the pump...
  3. T

    Fuel under air filter and intake.

    check around the lift pump
  4. T

    M1008 Fuel lift pump need HELP

    I found my fuel system was losing prime over time, and in order to start it, I would have to go through the bleed procedure by cracking the port on the fuel filter and cranking the engine. After I got the engine started, I noticed fuel linking around the lift pump. I pulled the pump, and...
  5. T

    M1008 air in fuel line

    Also, I dont have the problem when the fuel tank is filled. The fuel level is higher than the fuel pump, so the fuel doesnt leak back to the tank.
  6. T

    M1008 air in fuel line

    I was looking at the fuel pump more closely and I can see some fuel seepage.
  7. T

    M1008 air in fuel line

    Thanks. I have replaced all the lines recently. I am suspecting it is the fuel pump.
  8. T

    M1008 air in fuel line

    If my trucks sits for a few days, in order to start it, I have to crank it, then open the plastic cap on the fuel filter to let the air bubbles out, crank, bleed, crank, bleed, crank, then it starts. It runs fine, unless I let it sit for a week. Is there a spot between the tank and injection...
  9. T

    Brake issue, ideas welcome

    While I was working on my front brakes and bearings, I noticed that after I put the hub and the hub nuts back on, there was a bit of play in the axle (part that sticks out from the hub nuts). Is this normal? I also found a large nut laying in the caliper when I took it off. I couldnt figure...
  10. T

    Brake issue, ideas welcome

  11. T

    Fuel Injector Pipe M1008

    I now think that it was power steering fluid that got sprayed up onto the injector from leaking hose. I am replacing the steering lines now. I will start it up tomorrow and find out.
  12. T

    M1008 whining noise

    You are correct, as always. And what I thought was a fuel injector pipe leaking diesel was actually......power steering fluid that was sprayed out from a high pressure PS line that separated at the crimp.
  13. T

    M1008 whining noise

    Thanks. If it is the power steering pump, do I need to replace it immediately?
  14. T

    Starter bolt issues (again)

    I was having this problem until I removed the flywheel cover panel (next to starter) before bolting the starter on. I think it was preventing the starter from mating flush. Havent had an issue for a couple of years.
  15. T

    M1008 whining noise

    I am noticing a whining noise with a pitch that corresponds to the RPM. Sounds like the noise you hear when it is in 4wd low. I am thinking it might be the steering pump, water pump, or an alternator about to go bad?
  16. T

    Fuel Injector Pipe M1008

    I have fuel seeping out around the fuel injector pipe where it goes into the fuel injector. I tried tightening the nut a bit, but it doesnt budge. Do I need a new pipe, or can these be repaired?
  17. T

    where is my NP208 leaking from?

    I removed the transfer case and found the seal between the transmission and transfer case was the consistency of chalk. I replaced all the seals. For the record, the fluid leak was coming out of the vent tube on the transfer case. When I removed the fill plug, I got an unexpected heavy...
  18. T

    where is my NP208 leaking from?

    one more question. to lube the joint on the front drive shaft, I assume the drive shaft has to be removed? I dont see any grease fittings.
  19. T

    where is my NP208 leaking from?

    I removed the filler cap on the transfer case, and the fluid came gushing out. A lot of fluid. What would cause this?
  20. T

    where is my NP208 leaking from?

    I parked my truck (86 M1008) last night and this morning I found a puddle of fluid that is leaking from the shield on the transfer case. I cleaned it up, but it keeps leaking. This evening it is still leaking. It isnt a huge leak, but there is a puddle of fluid that keeps reappearing after I...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks