Search results

Maybe by removing the buds I can use a standard flat lug nut, and this will hub center, I'm oping, I haven't tryed it, any ideas?

Can anyone tell me If I can get a wheel with small lug holes to fit as a super single on my m915a1 4 ea Michelin X 395/85 R20 XZL regroovable radial tires and rims. Rims are 15" width and 46" height. Max lo... - Government Liquidation See the photo at the above gov liquidation site. My m915 uses...

MV at Schmidt brewery See the above site for video MV at the Schmidt brewery.

See the above site for video MV at the Schmidt brewery.

The old factory is the Schmidt Brewing company, and nothing actually broke, the truck looks tweaked, twisted, but it is ok, lost a bit of differential fluid though, the 5 tons don't like to lay sideways.

M820A2 Stuck in large hole While driving across a large vacant lot, I drove across a recently dug and freshly filled Pit. After days of trying and breaking everything, It was lifted out by local Huge Wrecker.

Some urban "Alpha Hotels", graffitied my trucks, Some criminals painted two of my trucks with their little gang signs, so I had to bite the bullet and go to Sherman Williams for three color CARC. Don't use soap to out line.

I have some M1A1 manuals too, I wont sell them on EBAY, does anyone know if they are classified?

Seal kit for m820a2 lift gate? Does anyone know if there is a list of seals to overhaul a m820a2 lift gate, mine likes to leak.

Here is a few of my m820 photos. Some knuckleheads tagged my m820 and m915, graffiti, so it left me no option but to paint. I bought my carc from Sherman Williams, military grade government specs. It was easy to paint too, no runs, dries fast. Photos to follow, iPads are hard to upload pictures.

I bought my m915 from GL Hooks Texas, and it ran great, except for sticky brakes, nothing a greasing didn't fix. Expect to buy batteries, although mine were good, the truck started right up 80 gals of fuel still in it was a bonus. It started right up, plus a lots of water in the stack made...

Yes sounds good where and when? CUCV are cool, if I can bring my 5 ton.

Disd you figure your starter run on problem, Today I went to start my super cold m820 with nhc250 engine, the starter kept turning, and I too had to disconect batteries, this is after I shut off both dash switches, whats causing it:? Starter solenoid?

Wow that sounds cool, have you drove it yet?

My 5 ton, temporarly black, and big singles, and better half

Congrats, I got three weeks ago, my EUC flew, it took a total of 11 days, I picked mine up for $1330, it was overhauled in 2004, and it pretty darn mint! 'cept for bad tires, after changing out the batteries, it fired right up, with a lots of rust water in the stack. Then I drove it for 1100...

Hi, Hey great Idea on the tire swap , I bought a ]M989A1, 11 ton, Hemat Trailer in SD, like new, and just bought a m915a with four of the duelies missing, I think I will short the trailer for the good of singles on the truck. By the way, does any one think this M915a1 is refurbished, it's an '84?

good question, I just bought a m915a1, is there room for a sleeper. Earlier this summer I put a peterbuilt on the back of my f450 ford superduty.

Thanls for the posting, I just bought a M915a1 in Saginaw, TX, and am hoping it will run with a jump, I need to driver it to Minnesota, and sugestions?

Ok, I just wanted to say that I hauled my M989 800 miles across South Dakota with a M109, duece and it pulled pretty good, not lots of hill climbing power, but with the air brake system it stopped well.