Official NC Denton Rally 2021 Buy/Sell

Floridianson

Well-known member
Steel Soldiers Supporter
6,853
1,059
113
Location
Interlachen Fl.
OK while looking for a 3/4'' tow bar pin for a member I found a surprise. Two 1 x 3/4 feet with correct non roll 3/4'' pins but no 1 inch pins. I will bring them to Denton and how bout $80.00 for the pair. I have been known to barter or work for the correct brownies.
 

Ferroequinologist

Resident railroad expert
Steel Soldiers Supporter
4,714
342
83
Location
Liberty Hill, SC
.
You are my hero! Thanks. Don't know about your personal stash of tanks - but I definitely appreciate you having a few :cool:

I am a bit of a pack-rat myself, so extras of everything is always good !
If you happen to have a spare locomotive and some track...
I looked at my M936 and the tanks I have- the driver tank on the wrecker is smaller than all the tanks I have. I'll still bring a couple.
 

Phoenix77

Well-known member
Steel Soldiers Supporter
195
335
63
Location
Greenville, NC
Update: I will sell both "big a$$" boxes; it fits in the back of the LMTV like a traditional truck box.

Its girth interferes with the function of the troop seating and because I am inexplicably insistent upon not removing the troop seats, I have decided to part ways with both boxes.

Also, in the process of climbing down to climb up a taller structure to get the pic of the inside of one, the wind picked up and slammed it shut on my left hand, fracturing my left ring finger and rupturing the tendon. There's testimony as to the heft of these things.
 
Last edited:

SCM35A2

Well-known member
Steel Soldiers Supporter
1,418
669
113
Location
Florence, SC
Does anyone happen to have an NOS or used, but in very good condition temp gauge for a M35A2 truck?? The one in my truck died & I'd like to replace it with one like it. I'll post a pic of it below...
 

Attachments

LanceRobson

Well-known member
1,610
136
63
Location
Pinnacle, Stokes County, NC
Might be a problem. Selling some property and they want to close on Friday. I am asking if I can sign a couple of days early like Wed. so I can still make it up there.
I can't speak to Florida law but when we sold our Upstate New York farm four years ago we signed all the papers a few days in advance of the buyer's closing so we could be elsewhere. I suspect you'll be able to sign early. Having bought and sold real estate in several states I know of no requirement that the seller be present for a closing.

Do you have any spare lids for the single depth medical boxes you have? I have an orphan bottom (2?) I'd like to get a lid for. Maybe two lids?

Best regards to all,


Lance
 

LanceRobson

Well-known member
1,610
136
63
Location
Pinnacle, Stokes County, NC
So, I finally dug some stuff out. The last few shows I went to in 2019 I had folks commit to buying thing, including a few pricey ones, I didn't put out to sell who never came by and in one case wouldn't even answer my messages. All I ask is that if you commit to something please send me contact info and come by as soon as you can to get it. I'll have a camper with a blue fade awning and a grey Ford Expedition with a "Retired US Army" front plate.

20210416_182518.jpg20210416_182619.jpg20210416_182645.jpg20210416_184354.jpg20210416_181915 - Copy.jpg20210416_182304 - Copy.jpg20210416_182404 - Copy.jpg20210416_181838.jpg20210416_183556 - Copy.jpg20210416_183707 - Copy.jpg

Large steel tool/part chest I want gone.... 38-1/2" x 16"x 6" (inside) 7-1/2" total. First $20 takes it. And no, the Miller Multimatic 255 is not included :unsure:

Size Large knee and elbow pads. The elbow pads are inside the knee pads.... $15

Budd wheel nuts. $10/all.

West coast mirror spacers and hardware. $10/all.

24 volt water and ration heater, lightly used (my personal one....) $75 OBO.

3/4" click adjustable 500 foot pound CDI torque wrench in great shape with the case. One plastic latch on the case is missing. two are good so it latches just fine. $125 OBO.

Medium tow bar (5-ton and smaller thrucks) all correct pins with 1" feet. The reinforcing collar upgrade is factory applied and not a field modification. $275 OBO.

More to follow....

Lance
 
Last edited:

LanceRobson

Well-known member
1,610
136
63
Location
Pinnacle, Stokes County, NC
20210416_174540.jpg20210416_133331.jpg20210416_133320.jpg20210416_133234.jpg20210416_181241.jpg20210416_181227.jpg20210416_181511.jpg20210416_181531.jpg20210416_181549.jpg20210417_160443.jpg

The short boarding ladder is the size for M101 or 105 trailers, M1008 or M998 trucks etc. The taller one is the size for M44/M35 trucks. It will work for M939 series truck but is a bit short.... both have the correct handrails and pins. $75 for the short one, $100 for the long one. Both for $150. SOLD to Matt444

Next to the ladders are 3/4" electrical conduit bent to replace missing boarding ladder handrails. You'll need to test fit them, then cut to length and drill the pin holes. $10 each.

Tool/Parts cabinets like many M109 etc shop trucks and trailers have. They were assembled and used for a few months in my car hauler before I sold it. No rust, good hinges and hasps etc. 25-1/2" wide, 24 " tall and 16" deep. I have two. $30 each.

Vehicular heaters. The first one is a 20K BTU gas heater and was working when removed but has sat on a shelf and been scuffed up for years. Low low price at $30.

The other two are NOS (new, old stock) 30K BTU heaters. Both still have the factory test and acceptance tags attached. One is marked "multifuel". I'm not a heater expert but have been told the other one is multifuel but will not guarantee that. I really don't want to put them back on the shelf. $60 for the one labeled "multifuel", $50 for the other one.

Shackles, the small one is a 3/4" hole trailer shackle. Sale priced at $30/all.

I have some other loose odds and ends and will have a lot of military and general history books, mostly from a friend's estate, for sale. If I dig out anything else of note I'll list them.

Best regards to all,


Lance
 
Last edited:

matt444

Member
Steel Soldiers Supporter
56
15
8
Location
Edgemoor SC
The short boarding ladder is the size for M101 or 105 trailers, M1008 or M998 trucks etc. The taller one is the size for M44/M35 trucks. It will work for M939 series truck but is a bit short.... both have the correct handrails and pins. $75 for the short one, $100 for the long one. Both for $150.

Next to the ladders are 3/4" electrical conduit bent to replace missing boarding ladder handrails. You'll need to test fit them, then cut to length and drill the pin holes. $10 each.

Tool/Parts cabinets like many M109 etc shop trucks and trailers have. They were assembled and used for a few months in my car hauler before I sold it. No rust, good hinges and hasps etc. 25-1/2" wide, 24 " tall and 16" deep. I have two. $30 each.

Vehicular heaters. The first one is a 20K BTU gas heater and was working when removed but has sat on a shelf and been scuffed up for years. Low low price at $30.

The other two are NOS (new, old stock) 30K BTU heaters. Both still have the factory test and acceptance tags attached. One is marked "multifuel". I'm not a heater expert but have been told the other one is multifuel but will not guarantee that. I really don't want to put them back on the shelf. $60 for the one labeled "multifuel", $50 for the other one.

Shackles, the small one is a 3/4" hole trailer shackle. Sale priced at $30/all.

I have some other loose odds and ends and will have a lot of military and general history books, mostly from a friend's estate, for sale. If I dig out anything else of note I'll list them.

Best regards to all,


Lance
I will take both the ladders
 

LanceRobson

Well-known member
1,610
136
63
Location
Pinnacle, Stokes County, NC
Ferro, no joy on the gauges..........:(



I'm clearly not the sharpest tool in the shed. I had these out on the garage floor in a plie and had to walk around them while taking other pictures and yet managed to not get them included.....

20210417_165840.jpg20210417_165855.jpg20210417_165804.jpg20210417_165648.jpg20210417_165719.jpg20210417_165923.jpg20210416_184017.jpg20210416_184001.jpg

CFP90 pack with internal frame. Appears unused. $50.

Two Gore-Tex sleeping bag bivy covers. Used but clean with no holes or stains and in very good shape with good zippers. Will keep your sleeping bag clean and both of you dry. $30 each or $50 for both.

1968 dated Vietnam era nylon flack jacket. Size medium in good shape-no holes, sun fading or tears. $75.

New Gore-Tex ECWS (Extreme Cold Wet/Weather System) trousers. Size medium short. They are cut pretty generously to go over several other layers so they might fit like large size if you only have pants on and not long poly-pro etc, too. $20.

Vehicular style 8-person First Aid kit with contents. It should be complete but, of course, anything with an expiration date will be out of date. Has scuffs etc. $25.

Best regards,


Lance
 
Last edited:

SCM35A2

Well-known member
Steel Soldiers Supporter
1,418
669
113
Location
Florence, SC
Anyone have a ladder for the like the taller with the correct handrail, the one for the M44/M35 trucks?? I missed out on a great deal lol, Lance I stole your pic too. I need one for my cargo trailer...
 

Attachments

SCM35A2

Well-known member
Steel Soldiers Supporter
1,418
669
113
Location
Florence, SC
View attachment 831502View attachment 831510View attachment 831509View attachment 831508View attachment 831504View attachment 831503View attachment 831505View attachment 831506View attachment 831507View attachment 831511

The short boarding ladder is the size for M101 or 105 trailers, M1008 or M998 trucks etc. The taller one is the size for M44/M35 trucks. It will work for M939 series truck but is a bit short.... both have the correct handrails and pins. $75 for the short one, $100 for the long one. Both for $150. SOLD to Matt444

Next to the ladders are 3/4" electrical conduit bent to replace missing boarding ladder handrails. You'll need to test fit them, then cut to length and drill the pin holes. $10 each.

Tool/Parts cabinets like many M109 etc shop trucks and trailers have. They were assembled and used for a few months in my car hauler before I sold it. No rust, good hinges and hasps etc. 25-1/2" wide, 24 " tall and 16" deep. I have two. $30 each.

Vehicular heaters. The first one is a 20K BTU gas heater and was working when removed but has sat on a shelf and been scuffed up for years. Low low price at $30.

The other two are NOS (new, old stock) 30K BTU heaters. Both still have the factory test and acceptance tags attached. One is marked "multifuel". I'm not a heater expert but have been told the other one is multifuel but will not guarantee that. I really don't want to put them back on the shelf. $60 for the one labeled "multifuel", $50 for the other one.

Shackles, the small one is a 3/4" hole trailer shackle. Sale priced at $30/all.

I have some other loose odds and ends and will have a lot of military and general history books, mostly from a friend's estate, for sale. If I dig out anything else of note I'll list them.

Best regards to all,


Lance
I'd like the shackles if they are not spoken for & if you just so happen to come across another tall ladder with the handrail like you sold to Matt let me know. Been looking for one.
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks