• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

What have you done to your HMMWV today/lately

davykeith

davykeith

Member
50
2
6
Location
Ellisville, MS
Luverne brush guard

Mounted my Luverne brush guard up last night. Leave it to me to do something back assward. First I put the tow hooks on upside down. Then I put them on the wrong sides nut facing the bracket. That prevents the guard from having clearance to mount..I digress. That guard is a heavy SOB. Fought with it for quite some time just to get the holes lined up. Any idea why these come with flimsy pins that don't fit the holes? Those seem to be useless and there are only two.

Ok, thinking outside the box here. Need opinions on this, as in go or no go. I'm thinking that I take the original l-brackets and flimsy brush guard that came on my HMMWV, modify the bracket by cutting a piece off and mount it to the rear as a guard for the body / tail gate. If I can back into something I will at some point. May keep a pine tree from caving my tail gate in. Gay or not gay? Yeah I'm not politically correct either.
 

Attachments

86humv

86humv

Well-known member
Steel Soldiers Supporter
1,692
489
83
Location
Texas
davykeith said:
Mounted my Luverne brush guard up last night. Leave it to me to do something back assward. First I put the tow hooks on upside down. Then I put them on the wrong sides nut facing the bracket. That prevents the guard from having clearance to mount..I digress. That guard is a heavy SOB. Fought with it for quite some time just to get the holes lined up. Any idea why these come with flimsy pins that don't fit the holes? Those seem to be useless and there are only two.

Ok, thinking outside the box here. Need opinions on this, as in go or no go. I'm thinking that I take the original l-brackets and flimsy brush guard that came on my HMMWV, modify the bracket by cutting a piece off and mount it to the rear as a guard for the body / tail gate. If I can back into something I will at some point. May keep a pine tree from caving my tail gate in. Gay or not gay? Yeah I'm not politically correct either.
Click to expand...
Bottom holes work better with bolts / nuts on Luverne guard .
 
davykeith

davykeith

Member
50
2
6
Location
Ellisville, MS
DatGuyC said:
Instead of 4 removable pins, replace the bottom two with bolts/nuts. This tightens it up a bit but still allows the guard to swing down when you have to open the hood.
Click to expand...
Ah, I see said the blind man. Ok that makes a lot of sense and now explains why it only came with two flimsy pins to use on top.
 
A

Action

Well-known member
3,581
1,551
113
Location
East Tennessee
davykeith said:
Mounted my Luverne brush guard up last night. Leave it to me to do something back assward. First I put the tow hooks on upside down. Then I put them on the wrong sides nut facing the bracket. That prevents the guard from having clearance to mount..I digress. That guard is a heavy SOB. Fought with it for quite some time just to get the holes lined up. Any idea why these come with flimsy pins that don't fit the holes? Those seem to be useless and there are only two.

Ok, thinking outside the box here. Need opinions on this, as in go or no go. I'm thinking that I take the original l-brackets and flimsy brush guard that came on my HMMWV, modify the bracket by cutting a piece off and mount it to the rear as a guard for the body / tail gate. If I can back into something I will at some point. May keep a pine tree from caving my tail gate in. Gay or not gay? Yeah I'm not politically correct either.
Click to expand...
I have a sifferent brushguard, but when i put it on, i set it on the ground upside down and backwards. Tilt in. Install pivot bolts. Swing up. Install pins. This may work for you, too.
 
Wire Fox

Wire Fox

Well-known member
1,254
158
63
Location
Indianapolis, Indiana
davykeith said:
Do show and tell this method.
Click to expand...
The pins for my Luverne guard are pretty stout. I believe they're 0.5" diameter detent pins. Perfect fit. Here's the trick to installing one easily:

1) place the rubber dampener on the lower pin hinges ONLY
2) hold guard up in-place as it would be installed
3) insert detent pins in UPPER mounting holes to hold guard in-place. You can temporarily use an under-sized bolt to hold up one side while you carefully line up and pin the other.
4) using the top of the guard as a lever, pull toward you to squash dampeners and insert lower pins or bolts while holding guard
5) optionally, remove top pins, lower brush guard, insert upper dampeners, raise guard, and replace pins for a rattle-free guard.

Sent from my SM-G530T using Tapatalk
 
C

Cameron187

New member
1
0
1
Location
Charleston, SC
Took delivery of my 2003 M1123 HMMWV today.This is the auction listing (sold 6/27/17): http://www.govplanet.com/for-sale/H...1123-HMMWV-2-Door-w/Truck-Body-Georgia/665797My EUC wait time was 190 days!Got liability insurance through Progressive (third call was the charm, after bouncing around because they thought it was too heavy for personal and too light for commercial).Arranged shipping from Albany, GA to Charleston, SC through VeriTread.Found a shop that agreed to take delivery and work on it... But the shipping went faster than expected, and it arrived right after a freak snowstorm. Yesterday was the 3rd snowiest day on record for Charleston, and we do not know how to handle it, so we shut everything down.The shop was closed due to the weather and I could not reach them. I do not have the proper equipment for a 24 volt jump start, so I put it into neutral and we pushed it back off the trailer.I still have not heard it running, the videos on the auction listing had no sound.Used a glock cable lock that came with a pistol as a steering lock, through the wheel and around the turn signal control.Pulled about 100 loose nuts and bolts out of it, probably left over from the removal of the armor.The deep water fording switch was on, so I set it back to "vent".I plan to remove the red dot A/C for now because it is not mounted to anything.Do not have my SF-97 yet. This forum has been a great resource for planning this project, thanks!
20180104_111931.jpg
 
twisted60

twisted60

Active member
610
241
43
Location
Jupiter, Florida
Got my SF 97 today, went down to Tax Collectors office and got temp tag so I can take it to the "inspection" scheduled for this coming Wen. I went prepared, Sf 97, Letter of reassignment from Iron Planet, Pic of my HMMWV, current Insurance, copy of FL DMV letter and a big smile.
Now tomorrow after part I need to put her back together arrives I'll take her out for a spin, get a load of diesel, put a few easy miles on her, have a good look for any leaks after I get her all warmed up then tuck her in the garage.
 
You must log in or register to reply here.
108,401members
163,706threads
2,303,261posts
1,806online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks