Tab Content
  • Ray70's Avatar
    11-12-2019, 12:00
    Well, back to working on this 005 again and looking for some guidance. I had it running fine after rebuilding the IP. I started it the other day and...
    98 replies | 8859 view(s)
  • Ray70's Avatar
    11-05-2019, 14:37
    On the solenoid, in short, yes you are correct. it's sole purpose is basically to turn the fuel supply on and off via the fuel rack which is attached...
    2 replies | 134 view(s)
  • Ray70's Avatar
    11-04-2019, 15:39
    Ray70 replied to a thread fuel tank won't drain in Generators
    Yup, the 802's are quite often clogged in the hose from tank to the petcock. Blow it back and it should clear it. Once drained you can remove it and...
    5 replies | 152 view(s)
  • Ray70's Avatar
    11-04-2019, 15:35
    K9medic, to answer about you clamp meter readings, yes if you were pulling 26A per leg then you are at 52A at 240V. So yes, about Full load. How many...
    45 replies | 932 view(s)
  • Ray70's Avatar
    10-28-2019, 21:42
    Ray70 replied to a thread MEP 002A Oil cooler lines in Generators
    So it looks to me like the lines you are simple -8 or 1/2" 37* JIC flare swivels ( 3/4" x 16 threads ) one line is 17 1/4" from center to center of...
    8 replies | 131 view(s)
  • Ray70's Avatar
    10-28-2019, 14:18
    Ray70 replied to a thread MEP 002A Oil cooler lines in Generators
    humm... that hose looks different than the hoses in the oil cooler kit the other person is selling. In the add for the kit it also appears that the...
    8 replies | 131 view(s)
  • Ray70's Avatar
    10-28-2019, 13:59
    Ray70 replied to a thread MEP 002A Oil cooler lines in Generators
    I have a parts machine with the shroud off, let me take a look tonight and see if I can tell what you would need to do to adapt it to modern...
    8 replies | 131 view(s)
  • Ray70's Avatar
    10-28-2019, 13:49
    Humm.... twisted wire on left side? When looking at the pump is the wire on the right side near the governor linkage arm? There is usually some...
    4 replies | 135 view(s)
  • Ray70's Avatar
    10-24-2019, 10:30
    Are you reading 245 on the gage or on a DMM, etc.? You really have no reason to go above 245 but there is a Potentiometer in the voltage regulator (...
    9 replies | 152 view(s)
  • Ray70's Avatar
    10-23-2019, 09:17
    Ray70 replied to a thread mep 803 help in Generators
    I second Kurt's suggestions on the switches. I've seen this same problem several times and cleaning the switches has worked every time for me!...
    21 replies | 622 view(s)
  • Ray70's Avatar
    10-22-2019, 09:09
    Ray70 replied to a thread MEP-8xx series fuel pump in Generators
    Yes, that looks like what they will need. The fittings themselves are cheap compared to the cost of shipping so I bought a handful of different...
    32 replies | 2599 view(s)
  • Ray70's Avatar
    10-21-2019, 14:51
    Ray70 replied to a thread MEP-8xx series fuel pump in Generators
    I just ordered 2 from Autoplicity, they have the E8135 in stock for $31ea. and $11 shipping for 2. Says they have 18 more in stock.
    32 replies | 2599 view(s)
  • Ray70's Avatar
    10-21-2019, 13:33
    Ray70 replied to a thread MEP-8xx series fuel pump in Generators
    For the primary pump you can use the E8135 and the older E1074 on an 002 and 003, you might just need to use a couple right angle fittings to have...
    32 replies | 2599 view(s)
  • Ray70's Avatar
    10-17-2019, 10:02
    Ray70 replied to a thread MEP-8xx series fuel pump in Generators
    If you are replacing the original square pump, the E8135 is a drop in replacement, no extra fittings etc. needed just reuse the 90 and 45 degree 1/4"...
    32 replies | 2599 view(s)
  • Ray70's Avatar
    10-15-2019, 15:31
    PM sent....
    4 replies | 212 view(s)
  • Ray70's Avatar
    10-15-2019, 09:44
    Hello guys, This weekend I decided to go back to working on this 003AASK with 3 original hours on it. When I last left it, I had redone the IP and...
    12 replies | 304 view(s)
No More Results
About Ray70

Basic Information

About Ray70
Location:
West greenwich/RI

Statistics


Total Posts
Total Posts
611
Posts Per Day
0.27
Total Thanks
Total Thanks
20
General Information
Last Activity
Today 11:45
Join Date
08-01-2013
Referrals
1
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Ray70
View Complete Feedbacks for Ray70
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0