Tab Content
  • Ray70's Avatar
    06-25-2019, 11:13
    Hello, Have you done any service on the machine? Fuel filters, oil etc? and have you tested it under a load? I'd be curious to see if the frequency...
    7 replies | 148 view(s)
  • Ray70's Avatar
    06-24-2019, 14:20
    Yes, they are about $75 for the NPT style, but... since you have some EMT tube in there too, the Universal flex joints for a car exhaust are only...
    24 replies | 490 view(s)
  • Ray70's Avatar
    06-24-2019, 13:49
    That's one nice looking set up! I can't tell from the pictures, but since you say you're getting a lot of vibration in the exhaust at the roof...
    24 replies | 490 view(s)
  • Ray70's Avatar
    06-21-2019, 09:18
    You can ohm out the wires on the sensor and if it appears the sensor is showing no fuel, try loosening the large nut on the top of the sensor flange....
    15 replies | 266 view(s)
  • Ray70's Avatar
    06-20-2019, 09:03
    Good advise Guy.... wish I read it before I installed it! I put it in yesterday and it runs! but I've got 2 issues to contend with. There is a very...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-20-2019, 08:50
    You can also try unplugging the white connector on the back of the fault light panel. Unplugging it will actually bypass all the fault safety...
    15 replies | 266 view(s)
  • Ray70's Avatar
    06-19-2019, 09:53
    Well, the pump is rebuilt. Made a few mistakes along the way that caused me to have to back up a couple steps, fix, then continue. But all in all it...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-14-2019, 09:00
    Ray70 replied to a thread mep002a in Generators
    Also, we need background history on the machine. Has it ever worked correctly for you? What was it doing that caused you to replace the AC...
    23 replies | 443 view(s)
  • Ray70's Avatar
    06-13-2019, 14:41
    Ray70 replied to a thread mep002a in Generators
    I assume you mean 65Hz then zero, not 95Hz. Can you give more detail on the replacement AC regulator? Was the machine dead then you replaced it...
    23 replies | 443 view(s)
  • Ray70's Avatar
    06-13-2019, 09:07
    So what I found is that the weight basket is a newer "1-piece" replacement, not the original with the flexible ring riveted on the back. So more...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-13-2019, 08:58
    Ray70 replied to a thread MEP-80x Fuel Return Line in Generators
    Agreed! If you're in there now, just go ahead and replace it all. That hose eventually fails on pretty much every machine. I would also take the...
    11 replies | 869 view(s)
  • Ray70's Avatar
    06-12-2019, 10:27
    If you have trouble again, while the pumps are out, see if the far end of the rack moves up and down. I believe there is a plastic cap molded onto...
    32 replies | 1091 view(s)
  • Ray70's Avatar
    06-12-2019, 10:22
    Ray70 replied to a thread MEP-003a No voltage in Generators
    Good work! I know swapping the CVT assy is not fun, but you got through and persistence has paid off for you! Glad I was able to help a fellow Green...
    121 replies | 2667 view(s)
  • Ray70's Avatar
    06-12-2019, 10:15
    I'm also not a big fan of U-ship. It works, but have found some sneaky shippers who will send you a question then once you give a reply they can...
    8 replies | 264 view(s)
  • Ray70's Avatar
    06-11-2019, 10:25
    Ok folks... I made good progress last night and now I have a couple questions for the experts... First off, I took the pump apart and as I got...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-11-2019, 10:11
    Hello, So are pumps 1,2 and 3 coming out of the rack and 4 stays in? Also, when this happens do you notice it right at startup, such that it had...
    32 replies | 1091 view(s)
  • Ray70's Avatar
    06-10-2019, 10:55
    Well, the IP is out of the machine and I've been looking over the -34TM in preparation to rebuild it. Before I removed the IP I took the transfer...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-06-2019, 22:10
    Ray70 replied to a thread Mep 006a Rear Oil Seal in Generators
    Oshkosh has it but sit down before you look at the price! If you try searching by the engine you may find more results. I also found a Federal Mogul...
    5 replies | 84 view(s)
  • Ray70's Avatar
    06-06-2019, 14:42
    Ray70 replied to a thread How to fix Blowby in Generators
    It sounds to me like you're machine is fine. Most 802's will smoke a little as you approach the 100% output range, some smoke more than others. If...
    70 replies | 1519 view(s)
  • Ray70's Avatar
    06-05-2019, 10:23
    Hi Guyfang. I'll try checking that before I remove it, but I'm pretty confident this gen was functional up until the day it was prepped and turned...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    06-03-2019, 09:09
    Well Guyfang, Looks like I'll probably be rebuilding the pump at some point. I did more checking this weekend and still no smoking gun as to why I'm...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    05-31-2019, 20:53
    Ray70 replied to a thread Mep004 in Generators
    Hi Brian, I know the bar you are talking about in Sewerzeuk's video's. Unfortunately I don't know enough about the buss bar to know why yours would...
    11 replies | 264 view(s)
  • Ray70's Avatar
    05-31-2019, 09:16
    That's pretty much what I was thinking for next steps, check vane pump and verify shaft spins while I'm in there. I have a steady flow of fuel from...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    05-30-2019, 09:19
    Well, here is where I'm at. I double checked everything under the top cover and reassembled. Took out the strainer on the fuel inlet and it was...
    94 replies | 8208 view(s)
  • Ray70's Avatar
    05-28-2019, 09:04
    Hi Guy, no worries, hope you are feeling better! I played with it for a few minutes yesterday and found that the throttle linkage was not actually...
    94 replies | 8208 view(s)
No More Results
About Ray70

Basic Information

About Ray70
Location:
West greenwich/RI

Statistics


Total Posts
Total Posts
558
Posts Per Day
0.26
Total Thanks
Total Thanks
19
General Information
Last Activity
06-25-2019 17:34
Join Date
08-01-2013
Referrals
1
iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For Ray70
View Complete Feedbacks for Ray70
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0