Recent content by 10Lugger

  1. 10Lugger

    FMTV High Speed Gears

    UPDATE: I still have these high speed gears: As stated earlier, I bought two complete sets plus one extra front. I anticipated buying another lmtv. My swap went easy. I will sell the front and rear diff set for $3500 firm. Pic. Available. Picked up preferred. I have no freight ship connections...
  2. 10Lugger

    Adding toolboxes to M1078. Anyone know a good place to stick them?

    Sent from my iPhone using Tapatalk
  3. 10Lugger

    Dump hoist and removable bed

    I have a hooklift on a Sterling. Hook heights vary. Unit could be installed, however the assembly weighs 2970 lbs. without fluids and pump. That doesn't leave much cargo allowance after you figure can or bed weight...
  4. 10Lugger

    Re-inventing 5th wheel

    https://m.youtube.com/watch?v=XixtZqpILm4 Sent from my iPhone using Tapatalk
  5. 10Lugger

    FMTV High Speed Gears

    Great! All new assemblies installed for $4k! I still think $3.5k is cheaper for the do it yourselfers! Sent from my iPhone using Tapatalk
  6. 10Lugger

    FMTV High Speed Gears

    After reading, looks like the value is around $3500 for the set. Someone can have them for that. I have all the paperwork from Texas purchase. Sent from my iPhone using Tapatalk
  7. 10Lugger

    FMTV High Speed Gears

    I have one pair of complete chunks/assemblies, plus a spare front. I bought two sets plus a spare, as I use my lmtv for work and can't afford down time. Years of reliability, have proved I don't need a spare set. Anyone interested in buying and picking the set up, let me know. Sent from my...
  8. 10Lugger

    Be cautious of west Texas windshield

    Thanks for the read. I clearly see the interweb evolving. 10 years ago the Op would have been unchallenged. His absence speaks volumes to me. This place is full of more heros then zeros! Sent from my iPhone using Tapatalk
  9. 10Lugger

    CTIS computer based diagnostics

    Are you using the program? Where did you source the cables? Sent from my iPhone using Tapatalk
  10. 10Lugger

    Is the CTIS angle valve serviceable

    Still holding air Sent from my iPhone using Tapatalk
  11. 10Lugger

    CTIS schrader valve and kneeling valve assembly

    I did a o-ring swap and it fixed mine. Simple fix with part numbers in that thread. Sent from my iPhone using Tapatalk
  12. 10Lugger

    adding new circuits to the fuse box - how?

    I'm following! Sent from my iPhone using Tapatalk
  13. 10Lugger

    Is the CTIS angle valve serviceable

    Picked up elbow today, looks like the other two on the truck. I didn't install yet because I wanted to see if suspected o-ring was the culprit. So far tire is holding air after O-ring change out. If not, I'll change out elbow, but at least I have one on hand. Thanks to all that participated...
  14. 10Lugger

    Is the CTIS angle valve serviceable

    The check valve kinda protruded out as I took the cap off, due to a little air still in tire. I just grabbed with my fingers. Below is a picture of parts after cleanup and putting a small piece of rubber between valve and union. I had to order o-ring and still waiting on it, but I reassembled...
  15. 10Lugger

    Is the CTIS angle valve serviceable

    I had to order o-ring and still waiting on it, but I reassembled and seems to be holding for now. I just don't trust the o-ring. Sent from my iPhone using Tapatalk
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks