• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by PoP PoP

  1. P

    mep-802a no start well pump

    You should make sure the knob/ selector inside the front cover is set to 120/240 single phase assuming it is not a 3 phase motor. (ONLY CHANGE with the generator OFF) Also make sure you are connected to L1 and L3 and the neutral connected as well as a ground rod.
  2. P

    5 ton Nordic TM and Cables.

    glo543zaadwyxg1 Would like TM and source for power cables. Helping local Sheriff dept. prepare for hurricane relief. This is a 5 ton 3 phase heat and air unit. It appears a 10 kw will run one. Not finding much info. I would think a 30kw would power 2 with ease. Can anyone verify or offer...
  3. P

    802/803 fuel return fittings

    I tried to remove a couple different ways. The quickest and cleanest was to use a set of End Nippers.. It bit the crimps right off in less than a minute. Surprised me after trying to grind off.
  4. P

    Newbie with an -803a

    https://www.amazon.com/gp/product/B01M1J97QM/ref=ppx_yo_dt_b_asin_title_o04_s01?ie=UTF8&psc=1 I love this on a plug.
  5. P

    New old stock 803 break in oil.

    Chainbreaker Good questions and thoughts. Yes 2 liter drink bottle full, drained from the bottom. It is new old stock , only 17 real hours. It had a bad hi temp switch that was not fixed and apparently shoved to the side. Yes the flap was down and in perfect shape. The oil did NOT have a...
  6. P

    802 803 831 Hi temp switch Problem

    ​How in the world I did not see that listing. I searched and researched. WOW! It comes up first when I searched for it! Just WOW. Thank you Zed254 Part ordered.
  7. P

    802 803 831 Hi temp switch Problem

    I was hoping someone would give a link based of their independent search. So I will throw out what I found. Is this correct, even if it is 5 degrees cooler? 220 F vs 225 F I think it would not make a diff. Deleted link to avoid mistake or confusion. Thread diameter could have been diff.
  8. P

    New old stock 803 break in oil.

    Thanks for the reply. . I verified the stick with another 803 and a 802. Like I said dumb question, but I am not a motor guy. Did take out 2 liter drink bottle full then checked it 9 more times to be sure over last two days. LOL
  9. P

    New old stock 803 break in oil.

    I have read up on the break in period and oil type posted here. My question borders on dumb question... none the less here goes. New old stock 803 17 real hours. Checked the genset fluids and found the (Break in oil) to be way over full. 1.5 inches too high on the stick. I drained out 2...
  10. P

    802 803 831 Hi temp switch Problem

    802 803 Hi temp switch Problem My new 803 has a bad Hi temp switch. This is IP, GP purchase, it came in with the wire unplugged. (New Machine 07 model) It reads open which it should as well as the one on my 802. When connected it will send the genset into HI Temp fault. Swapped out with the...
  11. P

    MEP 802A stalling

    You said NO fault codes. Press the fault code test button to check that they are working. Can you describe or video it stalling. A short video of it stalling would be helpful and be the quickest way to get better guidance. Video from about 5 feet and include front panel as well as the...
  12. P

    MEP 802A stalling

    The things that popped in my mind is Fuel cap vent closed and filters. Fuel cap still pinging in my head, with the time delays.
  13. P

    Libby 802 Coolant temp.

    I am doing those today and tomorrow. Just replaced the high priced braided lines at the filter. Had them made up this morning.
  14. P

    Libby 802 Coolant temp.

    Patience equals savings.
  15. P

    MEP-80x Fuel Return Line

    Okay I will replace them all while here. I needed the push to get me past the lack of experience on these lines. CSheath did a good job with the pictures. That helped bunches.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks