Search results

Started the road trip at 7:00AM in Slidell, LA. Destination Greenville, AL at 12:00PM. Truck ran great the whole way. No signs of over heating and the gauge reads properly. Average speed was 56MPH. Got there 15 minutes early. While waiting for the Morgans to arrive we checked the oil...

I am trying to determine the shipping weight of the MTVR A/C Kit. It is in a crate. :tank:

Can someone post the length of the boards that make up the bows for the 5 ton cargo trucks. I bought some new bow corners from Saturn surplus, but I need to fabricate the wood pieces that go between the bow corners. I plan to use 5/4 pressure treated lumber for the vertical pieces and...

Well I won a 1985 AMGeneral M923 at Ft. Polk, LA last week. We drove there Tuesday to recover it. It was a rainy day so no pictures of actual recovery. We arrived at Ft. Polk an hour early. We had to wait about 25 minutes before they let us through the gate. We drove out to parking lot in...

I went to visit Jeff Davis today in order to pick out a truck to purchase. While there I saw the horror of cut up M939 series trucks!!

I am having problems with my generator. It was running for 7 hours straight before it started to slow down and then shut off. Each time I restarted the gen it would run about 2 minutes and then slow down and then shut down. Today i replaced the fuel filters. It is still doing the same thing...

Filter part numbers for MEP-004A or MEP-0013A gen set I need the filter part numbers (NAPA if possible) for the MEP-004A or MEP-0013A gen set. It has a 4 cylinder White Motor.

I purchased the oil filter converter listed for the Cummins NHC250 engine. The kit had everything except the center mounting bolt. The instructions say it could be a 4", 4-1/2", 5", 5-1/2" , or 6" depending on the engine. I was wondering if someone that installed it already know the proper...

Yes I tried to search for them. Not sure if the M809 series belts for the NHC250 are the same. I need NAPA part numbers for all the belts for the M931 truck. Thanks in advance!

I have a M931 with Goodyear 11.00-20 on it. I got 60 MPH during the recovery trip home. (based on GPS unit) I was going to Super Single the truck with 14.00-20's to get more speed. After checking the spec's on the tires I do not think I will follow through with change. (not an upgrade) The...

I won my truck on GL 7-6-12. I had Jeff Davis recover it for me on 7-11-12. H towed it to his yard and stored it for me until today 7-14-12. We left my house at 8:00 AM and arrived there at 9:38 AM. We checked over the truck and after adding 15 gallons of diesel fuel we attempted to start...

Has anyone found any other uses for the M840 Shelter Dolly Trailer? I would also love to see some pictures of it in use. I know they have a cargo capacity of 9000 pounds so it can carry quite a bit. 1 Cargo platform (custom made) 2 Small Shipping container transport 3 Custom made camper...

I noticed there were the same 3 missing gauges on all the M923, M925 truck for auction at an undisclosed location. From the TM they are the Primary and secondary air pressure gauges and the transmission temp gauge. They are all removed and the lines plugged with bolt and teflon tape. Wonder...

CSM DAVIS, YOUR PM MAIL BOX IS FULL! I was told you were the man to contact about getting my M931 off the base @ Camp Shelby. Please contact me so we can make arrangements. Sincerely, Zev Weis goldneagle

I need 2 of the 11.00R20 XL's transported from Buchanan, GA (patracy) to Slidell, LA (goldneagle) I'm in New Orleans area. Any help would be appreciated. I am located Exit 80 of I-12.

I need to know the weight of 11.00-20 Michelin XL on Deuce rims. Weight of the rims would help. I think I got over charged for shipping my tires and want to verify the weights.

I have been looking at the major parts dealers as well as internet search with no luck finding a replacement front wire harness for my M52A2 restore project. I think any 5 ton multifuel truck wire harness will work. Does anyone have one of these in stock or know where I can get one? I can...

I finally got my WMO filter system put together. I've wanted to do this for a while but procrastinated until now. I have been reading threads on this site for a while learning how other members filtered and used their WMO in their Multifuel engines. I decided to go with sock filters for most...

I purchased an M52A2 from Justin Wehring this week. It arrived on Thursday Night. I only had 4 pictures of it to base my purchase on. Anyway it looks like it's gonna need a lot of work to get it to a safe usable state. It runs but doesn't stop! I am trying to decide wether to restore it or...

My truck has the Ether Cold Start Kit installed to the new engine. They never installed the actual cylinder. i was shopping around for the cylinder, but have not found a source. Looking at the Propane and MAPP gas cylinders and they seem to look the same as the ether cylinder. I started...