Search results

Worked fine for me too. Good info.

Shaft is out :) I got the shaft out. Looks to me to be bent and twisted! I'm looking for a replacement and some seals so I can put it back together. Thanks for the assist on the removal directions. Sorry about the mis-location of my posts. I hate computers! ballencd

Another Question About Disassembly of the M35 Winch ...Please: I am trying to remove the shaft that controls the winch clutch on the right side of the M35 front winch. I think it may be twisted as I cannot get it to lock in anywhere near the detents on the handle. I have the set screw out of...

The picture above of the drum is after cleanup. It looks like it could use a light machining but I'm thinking its not that important as long as it turns and can be tightened enough to hold a load. Seems like several folks on here have removed the brake altogether. The brake shoe material...

Winch Progress I have taken both ends of the winch apart. The input end was dry but everything looks ok. The band brake was too tight and had lots of residue from the brake shoe stuck in there. I pulled the drum and cleaned all loose rust/grit from it using a bench grinder with a wire brush...

I was hoping for a different answer. : ( I have the TM you indicated but I will print it. Looks like I could be headed for a complete rebuild of this thing but will take it apart slowly and see if it has an easy fix before I take it to parade rest. I have never taken any type of gearbox...

Gringeltaube, Hello again, First chance to try again today. I found a straight slot plug on lower passenger side housing of winch that I think is the brake drag adjustment cover but I could not get it to budge. I suspect I will have trouble getting every bolt out of the aluminum as I did the...

Gringeltaube, Thanks for the quick response! I bent my punch in the CW test and will try the brake loosening trick before I proceed. The post you referred me too was helpful and interesting. Thanks for finding it as I looked but had no success. I'll let you know how I fare when I get a...

Troubleshoot M35 Winch Problem Guys, I have a question and maybe a problem. I purchased a used M35 winch about 8 years ago planning on putting it on my M35 which has since been converted to a dump with one rear axle. I was told the truck it came from had been rolled and he parted out the...

I finally replaced the 12 volt pump with a 24 volt pump. The difference in buying pieces to change the 12 vdc to 24 vdc vs buying a 24 volt pump complete was only about $200 so I figured it would make sense to be able to use the 12 volt pump on a different project. So that's what I did. The...

Thanks guys for all the answers. It's not going to do me much good so I will try to sell it. ballencd

Here is the hinge setup I used on mine. The pins are 1", I believe, but my bed has been cut down almost 3'. I built a sub-frame of 2 X 2 x .25 square tubing and bolted it to the factory bed mounting bolts. I did remove the wood rail caps. I can pull the bolts and unplug my power and remove...

Thats what I was thinking. : ( Does it runs all the time when the transfer case is turning? Thanks for the info. I guess I will try to sell it as I don't have a 5 ton! : (

I was told this was a transfer case PTO off an M35 but it is too big for the back of the transfer case. Anybody know?

"See it here... CW for forward H & L; CCW for reverse. (when looking at the front side of PTO) That is always - as long as the clutch was engaged - and no matter if the transmission was in any gear or neutral. (the PTO is driven by the reverse idler gear, which is in constant mesh with the...

You are so right. What was I thinking. But I already have the winch PTO stuff! And I think the pump I already have is one direction since it has a larger input port then output port but I will look into that. I could go with just using one direction (i.e. forward only vs both forward and...

Yes, I think it is. At least its got 3 rows of seats and windows all around but I see what your getting at.

Guys, I have converted my M35 to a bobbed truck and installed a dump kit on it with a 12VDC pump and controls. I have trouble keeping the one battery it is hooked to charged and it is so slow to dump and drop. The pump is required both on lift and drop. No fun. I have a (not yet installed)...

I sold mine and I miss it! The kids needed more room so I went with a Suburban instead but I miss the simplicity and the diesel smell. I guess I could pour a cup of diesel in the floor of the Suburban.

I got a notice from Cummins yesterday that these engines will be available to order on the 29th! Still no price but that will have to be available on the 29th. Time will tell.