Search results

I needed some sand for the yard. The wife wanted to fill in some low spots. I got 8 yards of wet sand. The scale ot the pit said i had #17400 in the bed. Unloading it was not fun.

While driving this weekend smoke came out from under the dash. After pulling the engine cover at the dash off i found a burn wire that comes out of the rear of the engine harness and goes to the firewall that appears to be a ground. Does anyone have a wiring diagram for the humvee?

Is there any way to adjust the temp that the cooling fan engages? This one comes on at 210 deg and shuts off at 200. I used my laser heat gun to double check. And make sure the temp guage was reading right. It has a 180 thermostat in it but the temp will climb untill 210 when the fan comes on...

I just picked up a M1031 With the maintence bed on it. I'd like to install a 1008 bed and make it useful. Anybody know where i can get a good one?

Does anybody know where i can get a set of these steel pads? I'd like to use them as risers to help when the M127 trailor sinks in the mud.

Does anybody have the HP and tourqe ratings for the 250 NHC-250? Thanks

Here is some before and after pics of my resto. Well almost after. I still have alot to do.

I'm tring out a new resized pic of my M127 w/197 dolly

I hooked up my 105 to the M35 and started checking lights before i left. It's been a while since i needed the trailor. The brakelights don't work of the service drive is on. But they work fine if the swith is set to stoplights. The truck's lights work perfectly. I have installed a complete...

I know what your thinking, we've hashed this out a million times. After doing a search of old posts i didn't come to the conclusion i was looking for. What i'm wondering is, who is using synthetic gear oil in thier tranny? And for how long? About how many miles? Any trouble? Likes/ dislikes...

I stumbled on this web site a few minutes ago. www.lasmer.com They show to have deep water fording kits for the M35 series. Mabye someone can call them during buisness hours and see if they sell to private parties and if so how much are these kits.

How many feet of cable are sopposed to be on the M35's winch? Mine looks like it could take a lot more. Anybody know a good place to get new winch cable?

I just installed a vynl cammo bed cover this morning. The top has some pinholes. And the drivers side front corner has a tear where it attaches to a round black plastic anchor. The tear is about 1/2 inch long. Has anyone sewed, siliconed, or otherwise repaired small holes/tears in these? what...

Just got the deep water fording kit for my M52A2. Anybody have one of these?

Most MV's front T/S or running lights don't come on with the headlights. Has anyone rewired a M35 to make them come on with the headlights?

Does anyone know of a small clearence light that will fit in the small space on the 2 1/2 or 5 ton hard top? Mabye a LED?

Does anyone have or know where i can get a diagram for the multifuel series 5tons? Thanks

I watched a news bit last night about a kroger selling E85. It's the first one in town. It's running 40 cents a gallon cheeper than gas. I sure hope it takes off! It's out on HWY 6 though. About 60 miles away. Too far to do me any good. Anybody ever tried this stuff?

Does anybody know where i can find brake parts for a M127 flatbed? Are they interchangeable with 5ton truck brakes? Thanks

Does anyone know if you can swap 4th and 5th around in the 6352 like the 3053a in the duece is? It would make 4th direct and 5th overdrive. I know there would be a large gap between 3rd and 4th. One would probally have to run up to redline in 3rd and almost lug the engine going into 4th.