Search results

I'll be there, hopefully my deuce will be ready, camping with my parents again, they have been bringing my dad's grey CJ2A for 3? years now.

I have an M35 Gasser, and I have NO lights, BO or otherwise. checked grounds at turn-signals/parking lights, passenger headlight(drivers is still out gonna convert to H3's haven't done yet), and the BO headlight. I am starting to think that my three way switch is faulty or dead. is there a way...

That fluid is is only safe for diesels with NO glow system- either plugs or heated intake. It makes a lot of dead engines when people use it, even if the glow system is faulty, or "doesn't work" I put it in the same category as leak seal stuff, a bandaid that will cause an infection

Didn't do much today, went to go look at a rust free 6.2 Chevy short bed. Rust free, yes, but everything needed work, frame was patched and welded at least twice on rear shock mounts, top flange had chunks missing, steering box section repaired and plated, needed front end work etc. Not worth my...

Got fuel tank in, almost couldn't figure how to connect vent line-until I realized I was spinning the nut the wrong way, wasn't thinking about facing the wrong way. Also got cable for parking brake in partially, need to actually find some boots for it, maybe the GM handbrake boots I have seen...

Can you try another switch? Might be an internal ground on your dimmer

Cool, you want to buy me the phone and a plan so I can use that app?:roll: just playin with ya, but not everyone has a smartphone, or Iphone

with what speedometer cable ratio? I believe and probably wrong, but its a 1:187 for 11.00x20 tires, and 1:200 for 9.00x20 tires. depending on that and actual overall diameter of the tire you can range from as little as a 3% to as much as a 12%(I think, math might be off) difference. I have...

Air pack needs to be rebuilt, that is a vent line under the hood, when that spews, air pack should be rebuilt.

Just received an email from Iris Industries, For DOT 5 Fluid, Price for 4 gallons shipped appears to be around $175.00, Price/Gallon was $35.25, shipping $34.00. Price/Gallon is better then half of surplus, or anything else for that matter. Just an update to the price on the first page.

Yup gonna get 4 gallons, can use it in the M715 too when that gets done

All wheel bearings, knuckles packed, drums all adjusted, waiting for brake hoses, and waiting to hear back from Iris about brake fluid This is the converter I got, 20amp model, 25 bucks on Amazon, should work fine for a single cigarette lighter, most I see are only 15 amp at best Also put a...

I think he means worthless if you don't use it on road. If you only use a light bar 2% out of total use of the truck, was it really worth it? Opinions really at that point

Just a little input. But run covers if you don't less chance of being a "violation". NH law is 4 forward facing headlights, any more require covers

well my dad brought home the two races and inner bearing, total cost $47.50, just the outer from Amazon cost me $45.95. anyways, got the races installed, outer bearing should be in tomorrow, so final assembly tomorrow night. past two nights have been kind of wet and very humid, so I haven't...

Will most certainly try, biggest thing I want to install is a 12 volt plug to run a Dash camera, just ordered a 24V to 12V converter. also almost couldn't get a 392 bearing. My dads shop is Timken dealer, and well after talking with one of the Timken guys, they had NO stock in 6 warehouses...

yay!...or not, got drivers side all together, bearings adjusted, cleaned bearings for passenger side, pitted outer bearing and race, inner bearing race all scratched up, and no auto store in my town carries the 3994, 392, and 3920 bearings and cups, so I have to wait for tomorrow when my dad and...

What I do is start to pull drum and hub, until I can fit my fingers into the drum, then I can grip the drum, and put my other Hand where the outer bearing race is. This allows the most movement for me, without allowing it to tip when it is almost off the spindle

Did a little bit today, got both knuckles all greased, axles installed, wheel cylinders rebuilt, brakes all back together. Need to get more wheel bearing grease, already used 16 lbs, at least 10 of that was for the knuckles, another 4 lbs should do it to finish front bearings

some pics from last night, still need to adjust steering box, so that is why there is a missing bolt, and still want to blow out the brake lines, so output is disconnected from booster lookin at the picture of the steering box, guess I should have cleaned the frame a bit...at least it won't...