Search results

I believe it is: 6712NA call NAPA to verify. Should only be about $2 or so. TH400HD/3L80 I have pulled a fully dressed hmmwv engine that was locked up (5 gallons of water in it!) in about 3 hours.

Chris, You can pull the engine fully dressed...it is tight but it can be done. Hopefully the old engine turns over so you can disconnect the torque converter. A preventative knuckle busting move is to install the oil cooler lines and adapters on the engine prior to setting. Putting them on...

Yes on what NDT said. See picture of a test run setup. If that is your engine, please shorten the injector overflow lines or they will be snagged.

The -24P is very good to look at. Here is a setup prior to painting. Bumpers are cheap and easy to find, all the brackets take time and $. Good luck!

I have a couple. Make sure if you get one that it has all 3mwo's done.

twa, I did the same thing a few years back, only they made us expedite off the runway into the grassy area to allow a B17 comming in!

spicergear, I am all set on parts for this truck. Thanks though. The best way to sell that stuff is to use the unimog exchange. I am sure someone on the east coast is looking for those parts. The 406's seem to go a little higher than the SEE's but I think the SEE's have dragged the similar...

No video and when I am using it I never seem to take pictures. The suspension gives in the rear even though it has double springs. Using the backhoe to lift is fine if you have the stabilizing legs down. With them up, you see how it squats with an M37 bed suspended. The other coolness is...

This is what I call pre-SEE. My 1975 406 with backhoe and dozer blade (ex-German Military). Runs like a top, cleans ditches really good and pushes dirt and snow with ease. Remove the blade and backhoe in about 15 minutes and you have an awesome off road truck with a 3 way tip bed. Working on...

Hi Eric, Before I fixed mine, I bought a spare used muffler. If you can't fix yours and you do not want to eliminate it then let me know. I remember getting to the bolts from the manifold are a PITA.

I had a similar issue with a hmmwv. The return fuel line had blockage and when I clear it out, the engine ran perfectly.

37" radials on 16.5" hummer solid rims. Some of the H1 guys are looking for sets of these tires and they are starting to get pretty pricey. My last new set of 4 sold for $1000! This truck has a 6.5NA with 700R4 and 241 tcase(2wd/4wd). 70mph is where she likes to run!

Goodyear GSA are a good all around tire for the hummer/hmmwv. They are not made any more but are still sought after. I have a set on civi rims installed on a toy slantback with overdrive and they are quiet.

You have the later a2 winch frame extensions (channel type knee brace from lower a-arm pivot bolts to frame extensions) with an older 6k winch plate. Older knee brace is flat stock with a twist. See picture. So it may not be an M1038. Check passenger door sail panel for plate information.

Congrats! Nice clean looking tub!

Welcome to SS!

Derrickl112 post or pm price for one good tire. Also, if you have a spare hemett rim let me know. Pictures tomorrow of the vehicles.

Bob you still have an extra 1400x20 michelin xl 49ish tall? If so please bring. I was just there and it is a good turn out! Ill be there tomorrow too. Thanks Dave for the spaces!

I have a m37 used tank and a new generator tank that can be used for m37. Dave come over now and pick one for special host price.

Good chance ill make it. Ill have some parts there but most will be in the barn only a short distance away. 4 new bias hmmwv tires used hmmwv radials 900-20 tire chains only a few remaining heater parts Heater kit fuel Dog bones Drive shafts 1100-rims mich xl on m37 rims other tires on 16.5...