Search results

I did this on a 004 and in the simplest of terms I am emulating switch flips. Specifically the stop/run/start and circuit breaker. (Run, start, close, and not open) Id imagine as long as you aren't manipulating the battle short circuit the safeties will still work (mine do). In addition to...

You absolutely should have the set grounded. In your case if you aren't switching the neutral, (which is most cases) leave the generator neutral-ground bond open and tie the generator chassis to the ground bar in your panel ( should be 4 wire. L1 L3 L0(neutral) and ground. As for premature...

My pool does have a hot tub. It's essential to offset the geothermal ballast created by the magnetic Flux depending on the geosynchronous orbit of the nearest satellite. It all depends on what you really want. I have a fully automatic standby unit for about 2500. Sent from my SM-S908U using...

Depends on deal hunting. Most of my control components were sourced on fleabay. New from manufacturer, it was close to 5k in equipment, but since I'm using the older generation of devices I was able to get all the stuff for about 1000. Also keep in mind that controls my generator, fault...

If you want help let me know Sent from my SM-S908U using Tapatalk

My set has been modified enough to the point where it's automatic. Power goes out for only about 8 seconds. I used a slc 500 plc to control it. My speed control is a throttle servo driven from 2 outputs, the speed is monitored by output frequency from a hz to 4-20ma converter to an analog input...

I believe the 002 and 003 has a mechanical governor. Well. More of a compensator. I dont mind helping others with similar projects, the parts can get pricy though. Sent from my SM-S908U using Tapatalk

Yes. And my 004 is governor controlled (ok. I do controls for a living and was left unsupervised, but hey it's really really cool!) Sent from my SM-S908U using Tapatalk

It's how you retap a 12 lead wye head to single phase 120/240 split phase. If you draw the windings out it looks like a zig zagging line Sent from my SM-S908U using Tapatalk

I have a 004 at home and it's overkill. I did the zig zag conversion to it and last load banking it ran 72 amps for 4 hours. Sent from my SM-S908U using Tapatalk

Bigger things aren't really made for single phase but some of the older ones can be modified are sure you need something that large? Sent from my SM-S908U using Tapatalk

What are you powering? Is it a 3 phase or single phase load Sent from my SM-S908U using Tapatalk

If you are using this on a voltage higher than 32v you can use an eaton BK/ABC-30-R. it is of similar ratings where it counts. It does have a better interrupt rating (how much fault current it can stop before exploding) search on mouser for item 504-BK/ABC-30-R Sent from my SM-S908U using Tapatalk

I never tried the 003 on my home, but in my shop it doesn't like my air compressor. There are typically 2 things that set off a breaker, thermal and magnetic. Thermal is for the long overloads and magnetic is for the sudden shorts. Problem there is motors can draw up to 10x their current on...

Yes that can make minor adjustments. Use a multimeter to get an accurate reading. Be advised that the factory frequency meters are not the most robust Sent from my SM-S908U using Tapatalk

Puller is probably preferred Digikey or newark is a good place to look Might be worth looking at the possibility of replacing the bearing while it's apart. Sent from my SM-S908U using Tapatalk

Are you using the sets frequency meter or a handheld? I suggest using a known good multi meter to verify first. Sent from my SM-S908U using Tapatalk

Typically they produce 28vdc and 120 400hz. Aircraft use the high frequency because motors and transformers can be smaller and lighter Sent from my SM-S908U using Tapatalk

I can tell you for sure its for aircraft. The square 6 pin plug is for aviation ground power. Sent from my SM-S908U using Tapatalk

In that case an extremely cool paperweight? Sent from my SM-S908U using Tapatalk