Search results

RE: wheel drag then the axle shaft pushed the cap off the hu I would think the ujoint went out on the axle or some thing wrong in the third member . older mack with heavy rear ends had the same type of freeze plug cap and if you broke a axle it mould push out through this plug .maybe this plug...

RE: Wanted - spare tire carrier info for short wheelbase rig The m221 did not come with a spare tire carrier but adding one to the deck should not be hard . (pm) me your adress and I will send you some pictures of my truck and you can get some ideas .kenny

windshelds for a m211 measure 34 1/8 x 16 1/2 or real close to that . I used pieces of windsheld frames from 3 trucks to make one set .what ever these fix it's a good buy for nos.

I found a nother elbow in the shed it may be the one that fits the heater in take the hose end is oval I will ship them this week .kenny

I have part # 6 there are no numbers on it but the holes line up to the ones that bolt it to the side of the hood on my m816 parts truck . kenny

any chance the rear axles are the same ? any water in the third members or transfer case ?

it may be that the teeth on the pto gear and the gear in the transmission are making to much contact and need to be shimed apart . I would take the pto off put the cover back on and fill with gear lube and road test

The m816 wrecker (1985) I bought for parts with the same plan as M52a2 to mount the 45,000 winch to the rear of my 5 ton . any way the wrecker has a pto on the tranfer case that runs all the time the drive line runs to a nother gear box that has a drive line that runs to the crain pump with a...

my 53 GMC gets about 5 it runs good the 302 is said to make 130 horse power but it turnes both rearends all the time and the front is not always engaged but it's turning all the time .high gear running down the road is not direct but a under drive . empty weight is about 14000 pounds 5 mpg...

RE: Re: RE: Cab heater ? for M211 I have seen pictures of southwind heater mounted on the inside fender well just like hippiedude picture the intake is through the hood

the m151 kits work very nice in m211 just make a few mounts

RE: Re: RE: Transfer case PTO on the m816 the lever in side the door is in the corner beside to the rear of the seat. maybe some one will know about swaping pto from 2 1/2 to 5 ton ?

RE: Re: RE: Transfer case PTO checked the 816 the pto on the transfer case has no linkage on it .the drive shaft leads to a gear box on the front there is a shift rail that operates from in side the cab by the door ( in gear or out of gear ) ? out the back of this same gear box there is a...

RE: Re: RE: Transfer case PTO thank you I have m816 wrecker that I was going to tahe the pto off of but it look like it turns all the time with no way to put it in neutral . so I need a pto like the one in the picture that shifts in to neutral and that fits a 5 ton kenny

my 53 gmc had wet bearings on the back when I got it when I replaced the bearings I put it back together with the iner seal to make them dry . boyce equipment was the only place that had wear ring or sleave that fits on the axle (801) 393-0007 antelope valley (661)945-6788 has wheel cylinders...

is that pto made for a winch or a hydraulic pump ?

the bed looks like a m135 maybe dual wheel where added ? the cab cover brings up more questions when did these trucks have the small windows behind the doors ? I have seen them before . is the rear part of the cab where the rear window is could that original ?

If you do need some thing or even a pick up load let me know . I have to go now the porch light go's off at 10: 00 sharp

napa wheel bearing and chassis grease on every thing white and blue tube or bucket . if you have a seal leak oil from the rear axle to the wheel bearings it mixes . not good but it dose happen and no problem there is no way to know till you take it apart or the outer seal starts to leak .

I used the ramp the fifth wheel was missing when I picked it up . about the only things left are the front axle and one rear axle with out third member and the cab on a rolling frame . parts truck #2 has bad motor trans mission and linkage cab outer windsheld frame .one rear axle and other...