Search results

Helped a friend haul a CCKW home with the deuce today and all of the data plates are in German. Has anyone seen this before? Thanks for any help in advance.

Twin Sticked NP205 Front Axle Pops out of GearLike the title says, I twin sticked my NP205, scared of grinding the rails too much and allowing it to shift into Front High and Rear Low or vise versa I bought a set of rails from JKW Offroad. Quailty of the grinds looked good and while I was...

Like the title says, I twin sticked my NP205, scared of grinding the rails too much and allowing it to shift into Front High and Rear Low or vise versa I bought a set of rails from JKW Offroad. Quailty of the grinds looked good and while I was switching from the NP208 my truck came with we...

I posted this over on M715ZONE to, but as I think its more of a mechanical issure versus type of vehicle issue hopefully you guys can help me get this figured out. My original radiator was shot, so I got the aluminum replacement off Ebay that everybody suggests. Works GREAT! (well the first one...

Hey guys I've got a M715 that I was going to put a bench seat in. Everybody on the M715ZONE says that a 800 series deuce seat will work. Well I've got access to a 900 series 5 ton 2/3 bench seat. I know that it is larger but is there anyway someone that is blessed with two of these vehicles get...

After much debating and looking at my checkbook I decided to invest in a Spartan "lunchbox locker". It showed up today and I will try to get it installed tonight. Install seems pretty straight forward, the price was right and I don't have to pull the carrier and all that. If I get time I'll...

I have a little time at work today and thought I would share the story of what happened to the M1031 contact truck that was assigned to me while I was active duty. I was stationed in Babenhausen Germany as a heavy equipment repairer. I signed for the truck after arriving to my unit in late...

I've got an M1008 and am in the process of getting parts to convert it over to the M1031's NP 205 transfer case with PTO. The plan is to use this setup for a rear drag winch. Has anybody else done anything along these lines? I know electric winch's are cheaper and all that. I've already got a...

I know this subject has been covered before and I've read the previous threads. The other day the boss's m1008 pitched a rod or snapped the crank, of course this happened right before burn season started and thats our burn truck. We've got a 350 GM performance crate engine coming and are getting...

Gen 2 light works as it should at startup and is putting out the correct voltage. At night you can barley tell that its on. If you were'nt looking for it you wouldnt notice it. I've replaced the gen 2 alternator and battery and there was no change. Could the gen 2 relay cause this? The voltmeter...

I've seen several peoples cucv winch install and I thought I would put mine up also. Maybe give someone some ideas if they are considering putting one on.

My M1008 frontend is starting to sag. It always sat lower in the front than in the back. The front springs have a slight negative arch which, from what I have read, is normal. Last month I installed a heavy bumper and a MileMarker 12000 lb hydraulic winch. I run 34x10.5 Super Swamper LTB tires...

I bought a M1028 from Boyce Equipment and it starts and idles fine. But every now and again (every couple hundred miles) it acts like the the accelorator get depressed while driving. I dont think that it would be air in the fuel system because it starts and idles great. Maybe lift pump or...

I'm new here and I've been through the previous threads and havent seen a similar post so I hope that I'm not reposting a previously answered question. I have just purchased an m1008 not running. After charging the batteries I had power and the engine would crank but the glow plugs would not...