Search results

I have a MEP 004 with a electric problem. When the generator is on off position if I put the multi meter on switch S2 you get 24 volt as soon as you put the switch S2 on the run position you loose the 24volts and when you try to start it won't crank. if you go to the fuel solenoid when the...

the only light that is on is " no fuel". I do have fuel about 12 gallons

The problem I have it was that the generator hasn't run in a wile and the IP was stock. I finally got it running even with out that part for the IP. After a wile running it quit and the only way that it will run is with the wire from the positive on the battery to the positive of the injection...

I'm having a problem. I'M in Live Oak ,Fl . Right where the Hurricane hit and I need to have the generator .It have been a week without power or electricity. I have take the pump apart cause it did not want it to start. I have a part that forgot where it goes , I'm posting some pictures of the...

I need help on a MEP-004A. I'm trying to set the generator where I can used it on 3 Phase 416volts. Can someone guide to where do I have to set the switch in order for the generator to produce 416 volts on 3 Phase. Another issue that I'm having is that my temperature gauge and oil gauge are not...

Thank you for the info I will post again when I done

the pump I,m working on is the model DB2 Model # DBMFC433-1LK

Hello guys I'm still working on my MEP-004 trying to get it runing.I'm working on trying to put the seal kit on the Roosa Master and I need help on this part. When I open the pump There's a rubber ring that holds the governor basket onto its drive plate they are gone my question is . this...

Thank you for all your help,it is good that we have here someone like you with the knolLLLLLLLLLLLLLLLLLLLLLLQQQQQQ

I need help with the injection pump.Here is what I did. Remove the injection pump and open it to find out that it was very dirty inside, I went ahead and clean it to the best I can do without taking the whole pump apart.put the pump together an went ahead and install it in the generator.Start it...

Thank you you are a big help ,I think I can work with that,I will try later to post what type of generator. Thank you

thanks for the reply,but my question is how do i connect that one leg if it is 208 volts or 240 volts 3 phase.The one leg 120 volts is fine .but the other leg is 208 volts that is 328 volts, how do you hook the one that is 208 volts

hey guy's I'm trying to help a frieng hook a 3 phase generator to single phase at hes house. I know that L0 is ground or neutral ,one of the other legs is 120 volts,my question is how to hook the other L1 or L3 when they are 208 volts or 240 volts how do I go by hooking or where do I get the...

The pump is working,and the day tank is full of fuel Sometime the engine start and goes out pretty quick and sometime will state on for about 5 minute.right before it quit i have check for power at the injection pump and i have power there also I can hear the electric fuel pump working,now the...

i have this gen for a long time.never had an issue with it.The fault light is not on,i'm using the tank in the generator and the switch is in the right position.when i have the S2 un the run position I don't hear the pump, now S2 in run and S7 on then the pump comes on real fast, I'm not...

hello I have a MEP-004 that start but will only run for about 2 min.here is where I'm Check the day tank and it does not have any fuel.I turn on the battle switch on and the pump goes on and fuel will come out at the injection pump but no fuel and the day tank.

How do you bleed the air out on this system

no.Every thing looks like is in order.oil press,all the fault light none of then come on.The load is fine.Just a little low on diesel,but the gauge still reading about an 1/8 of the tank.