Search results

Okay weird question, How the heck do you reinstall the lift pump on the 6.2, I know its dumb to ask, but hey I was never from the 1980's. I know what the manual says, I just can't figure it out.

I'm having a fuel problem. I recently bought new glow plug relay because the old one was shot, but then I decided to replace the fuel filter. After replacing it, I attempted to bleed the system, but nothing happened over 20 tries. I even pulled the air screw, and applied air pressure to the fuel...

Okay I'm going to start a post combining two newer ones. First problem I'm having is my alternators. Some of you guys probably saw my post and I ended with I'm putting new parts into the alternators. Well every thing went well putting new parts into the alternators. Now when I went to start the...

Okay I started working on the m1009 recently. I have quite a few electrical problems especially with the charging system again. For now I'm going to ask about this ground wire I found on the terminal boards. From what I have seen on the alternator wire diagram it's a "suppressor". I was cleaning...

Okay I need to replace my tie rod on my m1009. It's bend really bad so that it slimly scraps the differential cover. Now it doesn't seem to be a flimsy thin rod. It's really thick I wish to replace it as the same one. (I will take some pictures of the rod latter) It's not the original stock bar...

I was wondering if any one here can get me a check list for the oil pan torque specs. I remember seeing some old post on 6.2 ,but can't find them. Okay I know you guys are going to say read the TMs. I really can't scroll around the TMs through different pages for spects with oily hands. ...

I'm getting the truck ready for college and for when I get my drivers license and, I have a lot of work I need to do to get this truck ready. Okay I'm putting a rear main seal in my cucv. I already have the pan down and the cap off the rear seal and ripped out of oil one. Now last time I...

Hey I was wondering how to remove the dip stick on the oil pan so I can drop it and replace the rear main seal. Dose it come off the oil pan?

Okay I'm finely working on my cucv so I don't have any gen-2 light when I turn the key in the accessory position. I checked the light bulb which was fine. Here's what I think the problem is. I just replaced the heater switch it didn't work so I replaced it and found out that it was burnt on the...

Well I have been working on my m1009 finally I took the dash apart. I'm making a list of parts to replace on the truck. Now my gen2 has not been working for some time scene I have had the truck. I rebuilt gen2 and burnt it up then replaced parts in it. When I turn the key to see all the lights...

Hey guys I need a tip on gaskets for the rear cap on the m1009 I looked in the TMs for something on that but couldn't find anything about the rear gaskets...I want to do the gaskets on the door windows and tail gate. Could some one point me in the right detection? or give to a link to a web site...

Is there any rallys in N.Y. or is the only good one in P.A.?

Hey guys I'm looking for a wed site that sells cucv pats I can't find a site except for one in Germany. Plus with cucv eletric gone I need alternator parts. So if you guys could point me in the right direction that would be a big help thanks.

Okay can't seem to get my charging system fixed. Heres the story at first the gen lights went out both when the truck was on and it didn't charge well. The volt meter was in the yellow and I didn't like that. Then out of all the sudden gen 2 light came on when driving the truck so I took the...

Okay I have been thinking about getting a dana 70 dually and putting it on my m1009 and a 60 in the front but will that help my off road performance? or is that a wast of time? What will that do to the drive train?

Hey guys I'm having some problems with my m1009 this is my first truck I have ever owned so don't think I'm a completed dummy for what I did. I'm trying to get it ready for I'm going to get my drivers license soon. Okay I replaced the battery's and I reversed the polarity of the battery's and in...

has any one ever seen or done a m1009 with a ring mount? I want to do this to my truck but, I'm afraid of crushing the fiberglass top. I want to know the right mount to use.