Search results

For a 802A the 2 connector one that goes in the Water pump/ Part number 82-22203. Anyone have a lead for me? Thanks!

Working on a MEP 004 picked up at auction. NEar the water pump and on the left side of the engine are two bare hose barbs 1/2 or 3/4 inch. I'll attach photos. I am wondering if a hose just goes between these? Also, does anyone have a current civilian air filter number for this. I have looked...

After much messing around and looking for part numbers I found a replacement MEP 802A water pump for significantly cheaper than most people want. It was on Amazon. You can find it at https://www.amazon.com/gp/product/B00JLBW3BS/ref=ox_sc_sfl_title_1?ie=UTF8&psc=1&smid=A12JDR3I03IC92 It comes...

My dad bought a 004 at auction and it is missing the Oil Dipstick, and the terminal connector board (lugs you put the loads into). Does anyone have a source for these? I think I found a dipstick on E bay maybe, but the terminal board I am striking out on finding. Thanks! Coley

Girlfriend also lives off grid and her 802A water pump shaft came apart and so we need a new water pump and fan blade. Have called Green Mountin several times with no return calls in the last 3 weeks so searching on here. Anyone have any suggestions? CF

My dad bought a 004 at auction and I picked it up for him. So far other than filters, I am seeing it needs a oil dipstick and the load terminal board where you wire in the loads to the genset. I am unable to find the dipstick anywhere, I have the NSN for it. The load Terminal I cannot even find...

I have a M116A3 trailer I sold a mep 802A off of, and my dad just bought a 15KW gen (MEP 804A I think). Gen weight is just over 2k and data plate on trailer says max load is little over 3K. Anyone ever try and mount a bigger genset on one of these? CF

I have many people I set generators up for that want to use them plumbed into a 300 gallon fuel tank here. I have had two problems with aux fuel systems. One the pump would not come on the other it shut off too late. I spent time trying to fix both before I tried to just bypass everything all...

I install off grid power systems for people. I have twice now paired up a 802 with a Magnum 4048 inverter and gotten the same issue. The magnum is a 48v inverter that puts out 120 or 240 and is rated up to 4k. It also has a charge controller that can take 120 or 240 to charge the batteries. It...

I have 2 MEP 802a sets I have installed for people who want to use the AUX fuel. Both are problematic right now. One the aux pump is not coming on, and the other the aux pump shuts off too late overfilling the gen. My solution I think I am going to do is plumb a tigerloop into the system and...

I have an MEP 802 that was running fine, but now will not crank. You can crank it from the Maint switch in the oil fill area and it turns over, but if you try from the main switch you get nothing. Any ideas? CF

Does anyone have a link to -10, 24 and 24P books in pdf for the 804A? Thanks! CF

I have an 802A I am working on that will not run the Aux pump. I have replaced the aux pump float, and checked that the pump itself works. I have also replaced the little box with the circuit board in it that is inline after the float. I am running out of ideas. The gen set has an autostart...

I have an 802A installed at my girlfriends off grid place and has been running fine till today. It shut down and I went to look at it. It is plumbed to a 500 gal tank with a auto/remote start installed. I noticed that the fuel pump located on the back wall left side is very noisy. It usually...

It will run for 2-8 minutes, then shut down with low fuel light. It seems to be vibrating more than normal. Any suggestions? It had new fuel filters. I may try putting new ones in. CF

MEP 802A keeps popping CB1 Breaker **SOLVED** Page 2 I have a 802A that has been running fine. I installed the remote/autostart from Inova Hightech. It has run fine for a few weeks. Last night it ran for 2 hours, then died. When I checked it. CB1 was popped. If I reset CB1, it will crank...