Search results

If you can find a clear image of a marking, it can be easy to render a vector file and make a duplicate. I'd be happy to try and cut some markings if you can find an image of what the marking or logo you want made. Send me a message.

Did you ever get your answer? The stock HMMWV wheels are +63.5 offset. 9" rim width, 7 inch backspacing = 2.5" + offset = 63.5mm+ offset. A -18 is setting the wheels 2.95" further out with a 9.5 wheel. I've been looking for wheels with a +63.5 offset, or close to it (with 9" wheel width)...

Count me in!

Looks like I was looking at the front, I need the rear. Based on the transfer case I have with part number 12340073-1 I need number 7 in that first part of the diagram.

Thanks. While I was waiting for replies I took a caliper and measured it. Seems to be 92 mm length and 27mm dia caps. This matches with a 5-1330X. TM shows two different part numbers for the same item, so not clear in the TM. TM lists 2-5-848X and 2-5-668X for item 21 in the propeller shaft...

I'm trying to determine what are the correct part numbers for the u-joints for the rear drive shaft. I unfortunately have the rear one that connects to the diff is all worn out. I'm planning on changing both ends of the shaft at the same time. When I disassembled it I noticed one was labeled...

Maybe your experience is different than mine but the back and forth I experience at a light has nothing to do with the suspension and ball joints. It's from the unbaffled fuel tank that sloshes back and forth at the lights. I have nothing to add about driving in snow with an HMMWV, I live in...

IN

I made a video of pulling the old green wheel and put a new black one on last weekend. I used the old horn. Torque the nut to 35 ft lb if I remember correctly. I used the AutoZone wheel puller they had but the smallest bolts they had in the kit were 5/16 and wouldn't fit. So if you get a...

Not sure if anyone has experienced this before but my 1992 M998 has an annoying clicking/knocking noise that I isolated to the front brake pads, seems like the right front. From what I can see when the rotors are turning the pads on my right front move up and down vertically. This causes a...

Can you send me a message or post where you got the tires? I need some BFG's. Thanks!

I'm planning on going, not sure if I will camp but will try and make it with my M998.

IN

If it's turning does that mean you have it jacked up? I would wait to jack it up until you have loosened the bolts.

I'm in the Katy/Fulshear area with my HMMWV. I'm always up for a meet. I went to an off-road meet up with the Hummer facebook club in Crosby during the Christmas holidays. They had H2's and an H3 there, I had the only MV. They don't seem to be too active (Hummer Facebook club). I plan to go to...

Yes, it all went well. once I figured out what I was doing. (y) (y)

Thanks. I did undo the nuts on the fan but there was not enough clearance inside the fan shroud to push the fan forward enough and then on an angle to get it over the fitting of the fan clutch. In the end I removed the 4 - 8mm hex bolts by connecting my air compressor to the fan clutch line and...

I'm hoping someone can give me some pointers here on replacing my fan. I had one blade break off recently and now I'm in the process of changing out the fan. 1. Can you replace the fan without having to take out the whole radiator stack? 2. If so, how can you get the hex bolt holes lined up in...

I used a gasket sealant because the gasket the pump came with was already ripped or more likely when removing it from the plastic wrap I broke it.

I'll check the bolts again at the brake rotors. Did this already when I purchased it but never hurts to check again. Something to add to my list next weekend. I have the 60amp alternator. Haven't researched if that's something easy to upgrade. Good advice on the battery disconnect switch. Thanks.