Search results

Heres my new pump I picked up today. Its a 1994 yanmar power 125GPM it was overhauled in 2007. It looks great. Im going to order some fuel filters and hose then go try it out.

Good info Ike. Im going to pick up a (1994 125B water pump Yanmar engine 125 gpm) today. I was looking for some info and found this post. It looks pretty new. I wonder if this bigger one has a l-70 yanmar. I guess I will find out later. If everything works out I will get hoses and fittings...

I use (Rapco carc substitute rattle cans) I did my entire m1009 with 1- mix lot case in 2 hrs. I also touch up my other green iron with it. I like it. Do a search on here there's 100's of threads and options of what paint people are using. Good luck.

Hello from SW-LA. Welcome aboard

Thanks Ike, I looked up the different metel problems with diesel. Thanks for the heads up. I think the kit comes with PVC or black iron pickup tube can't tell from the pic. If you have time can I see a pic of your set up. I was thinking about doing away with the drum return line being the aux...

Thanks. No problems. Although a proper M116 trailer would be nice. You can see in the pic where the gen walked over to one side while running. Once I figure out how i will set up my aux fuel system. I may bolt it down center of the trailer again. Or not I don't plan on pulling it around just...

Well heres my little setup. I just ran it on my 30x40ft shop only I have not tried it on my house yet.. I had a 12amp heat gun running and all lights,recepticles,fridge running. load 20%. When my 240v water well kicked on it surged to 50% for a few seconds. I only ran it for 30min. The AC...

Well I just added a 2nd AB-15 with Ms116-117-118. Both antennas are cut to to 110" from antenna mount to tip of antenna. It seems to work really well with the antenna un-tied. Im happy with it. I like the look and it works ok. Although I havent tested the range and 1- antenna probaly works...

This is what I'm running now. http://www.steelsoldiers.com/cucv/82468-batterys-3.html Oriellys Super Start extreme AGM 995ca My truck starts within a 1/2 sec. And I even run radio, winch, lights for extras. I used a 2x4 on top to help fit in the battery trays and there alot lighter than a...

Cool. Thanks for the info. Yeah the 002 is a nice smooth sound and the 016D sounds like a jackhammer

These are the battery's I just bought for my Mep002. http://m.oreillyauto.com/mt/www.oreillyauto.com/site/c/detail/SSB0/5172.oap?pt=C0423&ppt=C0005&un_jtt_redirect I have not installed them or tried them.

I hear ya. I would have got a RELIANCE 10 circuit transfer panel switch. But I have a 100amp subpanel running to my shop. The shop panel is running my 240v water well. So I figured I would get a 200amp transfer switch and be done with it. Just have to turn off 2-3 breakers on the house panel...

I just bought this Transfer switch. Its a manual GE transfer switch. Model TC10324R from Home Depot. $330 deliveried. I searched a ton of sites and and this one was the best price and what I was looking for my application. IT

Hows that charger holding up?? I just did a lot of research and decided to get that charger. Mainly just to charge 2-batts. In general but also a back up if my mep002 charging system isnt working properly. I just bought 2 super start 51r72 batterys. I only put 1 hr on the generator so dont...

Great thread!! So I'm installing a transfer switch soon just want to double confirm Here's the description. GE Outdoor rated 200 Amp boxed Transfer Switch; 2 Pole with Neutral *2 Pole Double Throw Switch with a Third non Switching Neutral Pole. includes 2 Inputs (1 for Utility, 1 for a...

Thanks alot for all your help. I will move the float around next time I try and report back. The pump is mounted and it's grounded on the outside of the slave port. I leave the ground in the same place while testing. Positive of batt to the pump works and 24v float switch output to pump no go...

Ok I got it. After searching old threads for hours I fixed the problem. My governor ip arm was sticky. I use PB blaster an kept working the arm up and down till the gov linkage would move it easily. I also tested the charging circuit briefly. The stator appears to be good. 35-40vac on the...

Getting close!!! I use 24v fully charged batt. The pump still works while mounted to the machine straight to the batt. With the 24v going to the float switch input I'm getting 24v to the output after changing a butt connector. I got power going in and out the thermal breaker. But when I...

Ok so I think I got a bad float switch. I got 40vac on each stator lead. I got 36vdc going to the float switch. I have NOTHING coming from the float switch and the fuel is low and the float is sitting on the bottom of tank. So I think the stator and rectifier are ok the little circuit breaker by...

I just ran my Mep-016D for a good hr with 1KW load. It did great. All gauges working. Hrtz and voltage looks good. With 1KW on it The load gauge showed a steady 75% I want to load it up to a good 3kw and see how it does. The only problem is I need to try to figure out the Aux fuel pump. I...