Search results

Yes, Interagency Motorpool can sell you the sealing ring/cup that is the main part in the air cylinder. The manufacturer is saying that the rubber parts can be troublesome after sitting a long time. I have a kit here that was made in 1990, much older than the ones just sold on GL, they are 1996...

I have one but the test set comes with it. JT out

To directly answer your question, Napa 5131 is the correct gasket for the primary. napa 5070 is the correct gasket for secondary/final filters Both of these gaskets are supplied with my primary and secondary/final spin-on fuel filter adaptor...

Dave, the t-case vent is on top and looks like the vent on each of your axles. It must rotate loosely and push and pull up and down a little. It will push fluid up your speedo cable too if it is plugged . Take care, John T

You will never see one of those Aeroquip fittings come off under pressure when using the supplied hose. But you will find it difficult to install the fittings all the way on. Do not use any petroleum based lubricant. PVC sewer pipe lube is OK and KY jelly is OK. (No flames...NO dumb jokes...

I met Dave and Dad at Memphis Equipment this morning, They have a great looking Deuce, I told Dave to enjoy himself and look at the trip as a memory being made. He sure does have some adventure ahead of him. Safe Trip, have fun. John Tennis

And welcome from Ephratah, NY near the Adirondack Park, JT

we are here, set up and ready to visit, hope to see lots of SS over here.

I'll be there Friday, warming the place up for your show. JT

Hi Joel, Industrial supply houses have the sprockets and roller chain you are looking for and Graingers and McMaster-Carr, both big industrial supply catalogs all over the USA. You also have an option to lower the air tanks as was the setup on the water and fuel tanker trucks. The tanks were in...

I did 7000 miles to the Pacific Ocean and back this past summer, in my M109A3 shop van Deuce. Granted, I had the truck in condition, with new tires, some extra sound reducing tricks too, but you will do fine, Wreckerman and you can check her out good before you head out for home. If you are...

They are Goodyear, bias ply mud and snow traction tread. BF Goodrich and Firestone also made them with similar tread patterns. You can still find them on firetrucks being auctioned off. JT

That was the only one I had, it's sold. JT

Avengeusa, I use the Dynomax 24216 in my upper stack on the M109A3 that went to The Pacific Ocean and back, 7000 miles in 28 days across the USA on US Route 20 and back on US Route 30. It has a stock, LDT-465-1D engine with 1D turbo. I burned diesel fuel and did not turn up the pump. I pulled a...

I have one you can PM me

I had to do some checking before I could post on this topic. The M35 deuce comes with a .187 speedo drive adaptor. To use 11.00 x 20 tires they install a .200 drive adaptor. I have had .212 drive adaptors, I installed one on my 1st JATonka 4x4 truck. It (.212) gives a 50mph reading while I am...

That sounds very interesting. And any thing that is interesting is possible. There is a current issue US military vehicle that has a powered trailer. PLS maybe? If I had thought of it, I would already be working on it. As it is, I think too much already. JT out

The OA-331 makes 146 horse power at 3400 rpm. It weighs 871 pounds without accessories. It is about the same size as a GMC 302. The bell housing is a standard SAE round. It will mount a Spicer 3052 transmission. JT

Maybe get a set of Mattracks for your ride, bunch of bucks and no getting stuck, ever again.

I am pretty sure He will catch up to you, He is a man of his word, way reasonable on price, and sent me a heck of a good Budd wheel socket. I have been using these since 1974 and he had the best one by far. John Tennis