Search results

Check temp. switch on the back of block next to fire wall drivers side.

Replaced weather rubber on doors windows ,vent windows,vents in kick panels,all went well but time consuming. My doors are now hard to shut , wife , son always forget the extra force it takes then they slam shut moving mirrors after a few days.Is there a fix or is it just Chevy doors? Thats what...

Hey what about the locks,did you buy all three somewhere? just where was that webbing in the frame on those more rare machines? Thanks Allen

Hey alrevup, also did mine some time ago just wanted to ask someone else if was any easier than mine were. Yes it was a task!!! But I put back brass two step rivets that we made on a lath here in our shop. I made the mistake of ordering the one piece first then sent back and reordered the two...

Hey, just curious , did you do vent window seals as well?

My family and I will be there also,can't wait this will be my first. We will drive in Fri morning.

After warm up I saw as low as 152 w/winter cover,idle,32 outside. With that full sweep gauge (mechanical) you can watch thermostat open and close as the gauge will move to 164 (same day) till open again. This is at idle. Different readings going down the highway at 45,50-up a long hill , pulling...

Many Thanks I just didn't know what they(pump)were. So is there a issue with the stock 85gpm? I'm not having any heating issues, I just added the winter cover due to idle heat for our winter here. I pull stock trailers all the time 3 days a week 4200lb empty 8000lb after loaded on way back but...

In Aug. I did 18 updates , pumps-water,fuel,oil,power steering, steering gear box,power steering hoses,new old redo on starter wire and connection , by the way I looking for a heat shield mine was missing(starter) anyhow thought I'd say that took me a long time plus did a gauge pack ,all temps...

My heat shield is missing, saw it in TM; but need one soon. Spent to much to not have it. How long do I have before heat gets me? Will someone show me a thread on it? I can maybe Fab one. Found thread but no for sure pictures just one off of another truck, not off of a 1008 or 6.2,

Just finished this pump in Sept. do the good job explained above clean,clean you'll do fine . I did the gasket,added a thin coat of sealer,a thin coat !!! let stand 10 min. then replace , do pump first seven bolts in back let seat an hour then finish torque . start then with backing plate,water...

Just finished damper Fri am 7 hours took time to look at it, alot! on the way in and out, job went fine .Did the cheap one, Doorman ! My thoughts were like yours so I did it. Any small amount of the wobble I saw is gone.

I have the autometer 2888 in my1008 see mount in photo ,126.00 plus hours of wire snake .Tach is good very little to do but wire to trigger,light if you want ? I did my light.

Changing hunt a little but while I'm here can you tell me what that relay is above fuse panel in your pic?

I don't know all there is to know but I think if your resistor isn't working you would know it soon enough , to much voltage . Check with meter at gp wire , + in wire connector ....-in a good chassis ground . Turn system on at key not start just cycle,... check voltage now and it should read...

My new card from cucv elec. is OK so far, paired with a trombetta relay.There are more than one trombetta that... I think is being used and works fine Part# 976-1211-010 is whats on mine, Part#974-1215-011-09 is OK also, there are even more but here is what I found lately!!! Watch real close...

Finished Damper job today all went well. Yea.. Doorman product but my wobble is gone, it wasn't bad but a piece of mind and a new bolt , new crankshaft seal, and a timing cover seal inspection no leak there. Seen my wobble early on but this forum was a wake-up call. Thanks again

Got mine coming a cheap one at that but at least it want do damage for a while to come that wobble was driving me crazy at idle. Doorman , we'll see how long it last then buy another. Sharecropper , tell us how yours' goes (fuildamper)? Found OEM but it was 162.00 so if I were going that...

OK now I'm on the same page with you. I looked some more nothing. I'll try more resources that I'm looking at

Lmc part#38-8112 Classic Industries part# is 373509211 they are not cheap but can be had.