Search results

one of mine is a 1952 model m35 upgraded to a2

my muffler is rusted out and i got a price on a new muffler for over $400. anybody know of a place to get a better price? in the mean time im going to just straight pipe it. has anyone done this? how much louder is it?

i purchased a international truck that has a new n-14 cummins in it and was going to use it until i found out how much insurance cost. now im thinking about swapping the engine out with my nhc-250 in the m818, will it fit in? would it be a straight forward swap? i just want more pulling power up...

heres couple of emails from his sister that i was dealing with trying to get my money back. Darrell is refunding your money. This is the second email from me today (the other is from my other account). Darrell says he has emailed you today and tried calling. I'm sorry my brothers...

this was just a few weeks ago

yeah this guy is a lying pos. he is on this site right now under the user name Kjb2007 Sergeant. so the guys that take care of this site might want to look into it. i posted a ad here about some m818 parts, he emailed me through this site and we made a deal. of course i didn't get my parts...

sounds like its needs to be disassembled cleaned and greased, my lever is tight also i imagine rust in bore of the lever, years of sitting i suppose

can you guys give me some guesstimates as to the value of a 5 ton pto with both front and rear outputs? i ts on a m54 i am going to part out, i looked at the one on my m818 its just a front out put so thought maybe its a little more rare? thanks

try using a outboard motor primer bulb to prime it with, there is an air bleed screw up by the air intake preheater crack that then prime it with the bulb. even after that its a pita to get it started, i have to use ether to get it to start after a lot of air gets into it,

sounds like your sucking air in to the fuel. do your engine rpms stay up after you let off the accelerator pedal? pressurize the fuel tank with air check all the hoses from the tank to the engine. mine had a cracked fitting on the fuel selector switch. my symptoms were hard starting. rpms...

just curious my trucks all seem to be prone to leaking gear oil on the left side front . one i just did a seal job on 1952 m35a2. i saw some steaks on the inside of the tire after a 400 mile run. my 87 m35a2cs is leaking also after i drove it the about the same distance. after studying it during...

sounds like gas boiling in the carb from heat soak through the manifold after shut down/ try using an insulated carb mounting gasket

i pulled this 500 miles. 40 foot container around 15000lbs. you have to lengthen the upper supports to make them work with a standard iso container. almost impossible to back i had trouble with mine tracking straight. make sure you check the air bags you can not get replacements. the brakes...

i drove it out boy was it slow at first until i got some fresh fuel a put a few mile on it. the tank still smells like varnish months later

I BOUGHT ONE OF THE 1987 M35A2C A FEW MONTHS AGO from warner and had some of the same problems. the fuel problem is from the trucks sitting with gasoline in the tanks and its turned to varnish, my clutch pedal was the same way. the only way to fix it ist to remove it from the shaft underneath...

ive been doing alot of towing with m818 its the only five ton ive used to tow with. can you guys tell me how your speed is towing . ill post pictures of the tow i did a few months ago from Wilmington nc to west va 500 mile trip . its seems to take for ever to get up to speed. and some grades say...

purchased this truck for the transfer case, and want to sell the rest of the parts, the engine runs its a lds 465 the fuel tank is in good shape, fuel pump is shot has good radiator good winch, drivers door great drivers fender great ect. please pm with need and offers. can ship

i have this one is in the classifieds for $2700

the inner seal is leaking you will have to pull it apart to fix it. i got my seal from od iron

has anyone done a swap to the gen 2 system? what would be involved?