Search results

I say keep it 24V its not that difficult. Read thease 2-threads they will answer most of your questions http://www.steelsoldiers.com/cucv/82535-convert-cucv-12v-pro-vs-cons.html?highlight=12v+conversion http://www.steelsoldiers.com/cucv/73068-convert-12v.html?highlight=12v+conversion

No pics Maybe when I get home in 2-months:( I have a plano plastic tool box centered. The tire is between that and the mount. It was a temp. fix but I think it will stay like that. By pushing the whole bracket forward it moved it 1.5-2" Its wedged in there tight between the seat,tail gate and tool

Doghead relay mod, Load test Batt. and clean battery connections would be a good start.2cents

I had the same problem when I installed my 33" spare in the back. Kinda did the same thing. My mounting bolts are not through the bracket holes. The mounting bracket holes are forward of the threaded holes and only clamped down by the large washers. Its also wedged in between my tool box and...

Is this CUCV related?? You can buy the SPOT SPOT SATELLITE MESSENGER :: HOME PAGE I think this would be good enough. Or you can Buy a used SAT phone and get enough pre-paid minutes for emergengy. http://www.globalcomsatphone.com

Fuel Filter- Theres alot of threads about spin on on here. But if you want everything you listed I would check out RACOR a little expensive but has all the extras your looking for. Tach- I know you said 2" tach. But the Tiny Tach gets the job done just as well. I installed mine in 20 min...

I havent done it but think I will use the 3M rubber coating or The Dupli-color Bed armor spray.2cents I will sand, prime, then spray.

You can buy the Civy "T" It looks like people or using pre-1983 model. Or you can buy the $75 Adapter. Or follow the wiring diagram and splice into it. The military plug is 12v. You can change your bulbs on your M101a2 to 1156-97 12v bulbs. I just did this to my M101A2 now I use it with my...

Im putting a front hitch on mine. Thats why Im getting one with a cradle so I can swap it from my other truck or trailer. Do a search like said earlier. Theres 100's of crazy ideas on how to do this. Heres a few...

8K-10K-lb I know WARNs the best but Im about to buy a 10K lb Champian wiinch with cradle for $400. Do a search under "winch" in the cucv section. Theres alot of threads and options.2cents

How old are the batteries? Did you get them load tested? Are all the terminals clean on battery clamps and bus-bar?

Very clean engine compartment wish mine look like that. Maybe one day. Check these 2- threads this was just covered I changed my gauge that was jumping and now it works great. Test the fuel gauge as per the TM-20 http://www.steelsoldiers.com/cucv/89000-m1009-gauge-problems.html...

Nice looking Oh-9[thumbzup]

Welcome from La. Nice Oh-9 Sounds like its on its way. Nothing better than fresh glow plug system and batteries. Might want to check that the starter bracket is installed and get the front wheel bearing checked greased in the future. Then should be good to go.

Really need to check the TM -20 manual. Do the testing as per the TM. It should help pin point the problem. Mine just started showing half full after I cleaned up the instrument cluster. But first I think you should check the ground under the dash by the E-Brake then the ground on the Frame...

I think the 2wd steering box is for adding cross over steering and the zero rate is a block to attach to the front springs to add 1" and move the axle foward 1 inch. Go to ORD.Com they have all the info on this. Offroad Design - GM GMC Chevy 4x4 Crossover Steering - Dana 44, 10-Bolt, High...

Im on the computer now. Was having problems with the message box but good to go now. Glad to see the site back.[thumbzup]

You can do a search for more detail. But I carry one of those (All in one jumper /power packs) that have everthing I need. Mines the Wagan Power dome. For cb and cigarette lighter. I ran a seperate 10 ga wire from front battery with in line fuse to power all my 12v extras like my CB, offroad...

Looks really good. [thumbzup]