Search results

Can anyone advise the correct part number for a radiator in a m1009 from autozone or O’Malleys The only number we can find is for the gas model but the transmission line connects are the wrong size Thanks

Does anyone know why following is embossed on the transmission of my XM211. THE TWO HALFS OF THIS HOUSINGMUST REMAIN TOGETHER AND WITH THE ENGINE

Does anyone know why the transmission will shift on low but not high?

I just purchased a m211 it has been sitting for 5 years does anyone know where I can get a complete insturment panel this one had been removed thanks. Will submit pictures if i can figure out how.

Can anyone advise how to remove the lower kingpin from the front spindle of a m422 thanks

Can anyone advise the best way to install turn signals on a m151. thanks

I just started my mutt for the first time today. The alt. Was not hooked up. The alt. Over heated and started smoking after about 30the seconds. It turned fine when I put it on. Does anyone have any idea what may have happened?

I just used a NAPA 572 fuel pump to replace the fuel pump on my M422. This is the pump used on the M38a1. I removed the pivot pin and swapped out the pump arm. So far everything appears to be working fine.

I just received a .125 gernerator 115 v single phase 400 cycle special purpose portable its very small. Smaller than a 50 cal ammo can. Does anyone know what it would be used for. I dont have a way to down load picturrs but the manuel that came with it is TM 5-6115-330-15. Thanks

A friend of mine agreed to sell me his mighty might in exchange for my mighty might project and some cash. His is about 90 % restored. Rebuilt engine, new winter top with doors and curtains and new tires and fresh paint. Can any one advise if there is a spare tire mount. I see them in the...

After I got the lifters freed up I tried to crank the engine. That’s when I found out problem #2. The oil seal at the canister blows out. I purchased a conversion to use a screw on filter. It works great. I also called bill Watson and was told to make sure the valve going to the carb. pipe is...

Can anyone advise if a rops kit will fit on a m151a1 or will it have to be modified. If it does have to be modified can anyone advise the process. Also is there a market for take off, uncut, m151a2 suspension parts. thanks fred

Can anyone advised what a fair price is for take off mutt tires. They have plenty of tread left on them. I am not sure if they are weather cracked. I am going to look at some tomarrow and would like to have an idea what they are worth before I make an offer. I know at least one of them is a...

I have to remove the wiper switch from my m886. Does anyone know the correct way to remove the knob without breaking anything? Thanks

Has anyone had this problem before. My gen 2 light will not come on and the volt meter is not getting any voltage. I remember hearing something about a similar problem that was caused by a relay. Both alternators are charging. 1986 m1009

Does anyone know where i can get a set of piston rings for a mighty might. I have my engine partially built but need a set of rings to finish it. Is there anything comercially available that will work?

I need help. I tried to start my mule and I have no compression. I put new jugs, pistons and heads on it last year but finally got around to trying to start it yesterday. I oiled everything up when i rebuilt it and soaked the lifters. I think they are hydrualic and at first I thought they...

Can anyone advise if a 360 out of a j20 jeep will fit into a m715 without alot of modifications. Will trans bolt up. Will motor mounts bolt up, ect. Thanks fred

Does anyone have a picture of the IR light that goes on the front of the M1030.

Can anyone advise which alt. charges the front battery. I have been looking but cant find the thread I need this morning. My gen #2 light began flickering when I turn the head light on. I checkec and only have battery voltage at the front battery. I have charging voltage at the rear battery...