Search results

2009 M1123 6.5 NA 4L80E in very good running condition. No leaks, none. Zero The only problem I'm having with it is the power steering feels very much like it has air in the system/low on fluid- however the black lunar lander fluid reservoir typically near the fuel filter on the top of the...

I am in the midst of repairing a catastrophic failure of my front drivers side wheel bearing in which all moving parts were destroyed. I sourced the part numbers for the bearings and races, but I need to source the two large nuts and spacer/washers that held it together. I had to cut mine in...

I was driving it to pick up a few thousand pounds of rocks when I noticed a "jerk" in the steering wheel that was not because I hit a pot hole. I shrugged it off and suddenly it became violent and I went for the brakes to slow down and get it under control when I realized I had no brakes and the...

I'm replacing the fuel filters on my truck and I bought the NAPA #3512 for the two large secondaries per this forums advice. They look just like this http://www.fleetfilter.com/mm5/graphics/00000001/33512.jpg They're a good match for dimensions but they have the big sheetmetal screen on the...

I got them from user " atankersdad " here, brand new in the wrapper for less than I could buy a set of cheap 12v KC lights from Autozone, and they're way brighter. Their original function was to be driving lights for the M1A1 Abrams but I don't have anything that cool. Like all surplus stuff...

I have a 395 spare for my truck that is 10 kinds of in the way in my garage, and isn't doing me any good should I get a flat out on the road if it isn't on the truck. I'd like to mount it somewhere on the truck and I'm looking for ideas. Its way to big to go in the factory spare location and I...

I'm trying to assemble my WMO recovery/processing kit and I have everything together except for a filter for my pump. I've found one online that is exactly what I want, but its about 150$ more than I think its worth: By-Pass Filters and Mounting Systems I want a spin on filter (with a common...

The LDT multifuel in my Deuce has a full time fan. I recently discovered the 900 series trucks have a heat clutch on their fans. I would like to stop my fan from turning when it isn't needed for a quicker warm up and maybe pickup some extra mileage per ton of fuel it uses. Pretty sure the 900...

I need to replace my emergency (pass side) gladhand as the boot is ripped and leaking air slowly. Its old crusty metal and I have a feeling it may not survive being removed. Is the inlet diameter and threading the same as a civ tractor-trailer gladhand or do I need to source another M35 specific...

What style is the plug to fit the accessory socket on the outside of a Deuce cab? I want to fabricate a "work light" to run off of it. Does it have a built in ground already in the connector?

Sourced some XMLs, going to use my A2 rims. Research shows I need a 14x20 innertube and flaps to protect it from the radial tire I am installing it in. Called some local truck supply places and only place I found that carries them wants 55$ a tube, more than half what I even paid for each tire...

when the wheel is "locked" to right or left (doesn't matter) or close to "locked" and you begin moving forward in any gear it makes a god awful grinding kind of noise. loudly. sounds almost like a big clutch that lost its springs but as soon as you straighten out it quits and everything is fine...

I have searched but cannot find anyone trying to run STRAIGHT 87 octane regular gasoline in their multifuel deuce. I am asking because the one I am about to look at is about 70 miles from me and gas is almost 40 cents a gallon cheaper than diesel. so. Straight gas, will it work? EGTs stay...

Hello, I'm about to purchase my very first M35A2 as soon as I find one in the shape I want not on the other side of the country. After getting any basic maintenance necessary completed I really want to single it out (note; not bob, retaining all 3 axles). I have gathered that for a factory troop...