Search results

just found a oil seepage on driver side of motor, now white smoke at start up then black smoke at running temp only going though 2 quartz oil in 8 months no drips im thinking head gasket . any help

ive been driving my deuce for a long time and now i find and oil seepage on the driver side of motor.looks like its running back to bell housing and down ,but does not drip oil.and now there is white smoke at start up but then gos to black at running temp only looks like down 2 quartzs oil in 8...

465 Ld motor what is the correct timing before top dead center,and how do you turn the motor to get it there?Thanks

I have a question on the incab heater. why does the resistor get very hot when the fan is on low but works fine on hi? could it be the blower motor is bad?Thanks

Just looking for couple possible answer's. I drove my deuce with a multi fuel engine this summer up to the mountains.drove it about three hours highway speed 50-60 mph.when i got there oil was leaking from the rear main seal lost about a gallon and had to take the fording plate off to spray the...

Its been said to me the why to check oil is hot, then no cold with a single oil pan with a single drain hole its better to check cold because all the oil is in the pan.But with the deuce its has a split pan with two drain holes so all the oil is not in the section with the dip stick in it.So if...

Hello, had to add brake fluid I can build the pedal up to firm but it will lose it in seconds. The truck did not run in years,I dont see any fluid leaking at the wheels so could it be the airpak?I bleed the airpak and brake fluid comes out so not sure..also there is a air line going to the blow...

hello all, Got my motor running on my m35a2 truck I found in a homeowners field then I was working on the brakes and I think blown a air line somwhere near the pass front tire all the air ran out quick so I didn't have much time to pin point it and it wont build any air to tanks is there a air...

Just a question if you need a radiator can you use any 8 gallon radiator or do you need one that's made for the truck??I'm working on a rescue m35a2 and someone put a tree branch in it two holes one inch dia.. nice huh.thanks.

Hello, I may have a battery issue not sure, does anyone have trouble starting there deuce after 4 or 5 days? I have a solar charger that works great but 3 to 4 days with no sun is a problem, I've checked for dead short found none, the front battery closest to the front of truck is dead the truck...

the drain is on the bottom of t-case how do you fill it with gear oil?

Hello,I'm going to be doing the rear main seal and a new clutch in a m35a2 with no winch divorced P.T.O. Where i live I really don't have a good place to take the truck apart,it's dirt or uneven asphalt.Plus I have never done this job before and really don't want to get the job half done then...

I watched alot of videos on transmission removal this looks doable. When you put the trans back in place is there any special way that it lines up? Any help on that? thanks

Hello all, I just got done putting a new steering wheel. The old one was cracked and looked like crap,anybody looking to do this job get a steering wheel puller or your cutting the old wheel off.The new wheel looks great and works well its 18 inch vs. 20 stock wheel not much different for turning.

Hello all before I buy them does anyone know forsure that 1400x20 goodyear at2 will fit on the rim? And then go on a bobbed deuce. The tires are on a regular deuce rim with split ring now. I have heard that's not safe so I finally found combat rims is this the right move or not??? thanks

With m35a2 parts getting harder to find I need a hardtop for mine.I had a guy tell me that a m211 top is close to the size of a m35 for a half cab does anyone know if it needs to be modified to fit?? I cant afford the cost of a m35a2 half cab because prices have gone way up low supply high...

Does anyone know where or who as the operators manual for a m35a2 from 1977? Is this something I can print out or maybe buy from somewhere? Thanks..

Hello all, I'm running air lines to the back of my deuce for a trailer. I'm thinking this is not like regular air lines one for service from the pedal and one for continuous air to release them. So hears the question do both lines need to be a service line from the pedal so air is only applied...

What would cause oil drip's from excaust pipe by the joint by air cleaner??

Where the speedometer is connected there is a part with a screw which is connected to the seal that go's into the transfercase. It's threaded on both ends how does that part come off??This is on a m35a2. It should just turn with a wrench but is that screw holding it on? thanks