• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by Kharville

  1. K

    In-tank Parker pump blowing fuses

    I found some time to look at this further. It appears the black wire that powers the pump shorts to ground if you move it just a little. As you see in the photo, the mesh wire is broken were it bends to go into the tank. Anyone know if that black wire can be repaired of if that wire even...
  2. K

    In-tank Parker pump blowing fuses

    I recently performed fuel filter replacements on all my fuel filters. After changing them the truck would not start. I found the lift pump fuse blown. I replaced the fuse and it blew again. I took the pump out of the tank to troubleshoot. I submerged the pump in a bucket of diesel and...
  3. K

    Air Pack rebuild Leftover Part

    So the small end of it goes into the springs and then the plug last?
  4. K

    Airpak rebuild

    It is item 16, the oring between the halves.
  5. K

    Airpak rebuild

    I am just about done with the rebuild but nobody seems to know anything about the oring between the two big piston halves. It looks beveled. The kit did not come with it either.
  6. K

    Airpak rebuild

    I ordered and received my rebuild kit. I am starting to disassemble now. So far I see nothing out of the ordinary. What normally goes wrong with these airpaks? A particular oring? All I know is brake fluid is blasting out the firewall vent line and the PS article said it was a symptom of airpak...
  7. K

    Airpak rebuild

    Hi all. I'm rebuilding my airpack and noticed teflon tape on the threads of all the non-compression fittings. Is that the best idea or should I use a liquid thread sealant?
  8. K

    Heater hoses

    I am confused. The one on the right is my Deuce. :confused:
  9. K

    Heater hoses

    The article I posted is the same one you mentioned. "Multifuel 2.5 ton". It is for Deuce. Where did you see HMMWV?
  10. K

    Heater hoses

    I am trying to validate my heater hoses against the PS article below. Is my top hose where it should be? I can't really tell from the quality of the picture.
  11. K

    10W Non-detergent oil as lubricant in the fuel

    Anyone have any thoughts on using "non-detergent" 10W new motor oil instead of 2-cycle for the added lubrication to diesel fuel in the Deuce? The reason I ask it that a local store has the 10W and 20W for less than 2-cycle oil and diesel fuel for that matter. Serious sale I guess. (e.g...
  12. K

    Low air buzzer

    When it gets warm beyond the possibility of ice I will see if it goes off. I drain tanks after driving.
  13. K

    Low air buzzer

    Went out to see how the Deuce would start in our first cold weather here in the south this morning. Started perfect with a few more turns than usual but 3-5 seconds total with no assistantance. I went back inside to let it warm up and when I came back out air pressure was normal but low air...
  14. K

    Trying to find a thread I read earlier about Deuce build

    Start at post #117 in the link I gave. He begins describing the vent lines ,etc. and pictures follow in the next few posts. I don't want to leave you hanging....
  15. K

    Trying to find a thread I read earlier about Deuce build

    Sorry. Here it is. #118
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks