• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by Tanglewood16137

  1. T

    starter

    this should work and its 12 volts so they could be converted easily to a 12 volt system https://www.amazon.com/STARTER-TRACTOR-HERCULES-1987-1988-1990480/dp/B008XOJ718
  2. T

    parade setbacks

    Well i will need to get a new hose for the remote Reservoir kit i got from you was getting truck ready to go for memorial day parade and it is probably nixed my hose sprung a leak all over. Some **** rodent decided to use it for a chew toy and prferated it for about a foot in the middle of the...
  3. T

    What did you do to your deuce this week?

    Well we worked for a week and a half rebuilt master cyl bled brakes installed spin on conversions to all places removed and partially cleaned up fuel tank new air filter cleaned and touched up paint and ran it in memorial day parade. It had been sitting for 2 years un used. Rod
  4. T

    Master Cylinder Remote Reservoir

    Hello Someone on hear is selling them but i cant find the post Rod
  5. T

    Disc breaks anyone?

    So you can run unaltered hemtt rims no adapter plate needed
  6. T

    goodies on the move

    I saw a 800 series 5 ton tractor on a flat bed and a long box trailer in cammo heading east on I 80 at about 7pm tonight someone must be getting a now ride! Rod
  7. T

    Need 24v to 12v converter for dump bed

    Just wire the pump up with 24 volts it will be fine actually it is easier on it than dumping a load on 12 volts. those motors can handle up to 48 volts. How do you think they get the the nigerian boys cars to hop? 48 volts to a 12 volt pump so it will pump fast enough!!! DUH
  8. T

    M35A2 Insurance in Pennsylvania

    i am in poa not far from butler mine has a class 8 registration and my ins is 232 a year. thru erie insurance
  9. T

    Cracked my trucks bumper markings

    Carnac my dad was in 99th arcom out of farrell PA was in 858, 402, 475, and 347 and over a 35 year career in reserves retired out of 402 in 89 Rod
  10. T

    Deuce by the roadside!

    guys you could write a jingle going to busty hearts on my way looking for some M V parts well i need to think for next line i am not to good with lyrics
  11. T

    Deuce by the roadside!

    the ones on corner of 59 and 46 seen them 2 times in past 3 weeks been up that way i see 5500 for 1 and 6000 or 6500 for the other kinda rusty for that jing then there is this mv hoarder up by the nudie bar he has them all over the place. Joe just kidding i had to say that!!!:roll: Rod
  12. T

    Manufacturers of the Deuce by year?

    my 1970 has it titled as a 1970 AM General. I don't know what is right Rod
  13. T

    10 bolt hubs

    what i was pointing toward is using the bigger lug studs like ones on commercial trucks so all you would nee is your outer hex nut so you would just need the 10 for each side up front Rod
  14. T

    10 bolt hubs

    Looking to see if there is any interest in 10 bolt hubs to fit a deuce made of good steel would it need smaller lug studs to match front or use big ones so you can use existing hex nuts off old duals. Were hoping to be alot lower than a wicked six made of aluminum. need to know interest before i...
  15. T

    Gulfway Ins. Limitation WOES!!!

    i got mine thru erie insurance and its 235 a year and its licences with a class8 commercial plate
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks