Search results

You could use a carburetor choke cable, I found this one at autozone P/N 2450. Hope this helps. Cheers :beer:

nopics

:funny::grd:

I found this on the web, I wasn't sure where to post this. I am sure most of you will find this vehicle very interesting. Cheers :beer: http://www.motortopia.com/videos/vie...prototype_agl4

Mine is insured by USAA. They too had a problem with the vin, Apparently it did not exist! Cheers:beer:

Thank you Warthog for sharing your knowledge once again with me and anyone who might have the same doughts about which flex plate to use on the 6.2. I will order mine today as I had to turn my engine by hand again for the second time to get past the blind spot on my ring gear so that the starter...

Thanks Crash, I am not blind after all! I just looked at the wrong parts TM. But if you go to the autozone's web site and look at P/N FRA-142 and FRA-143 you will understand why I am confused as far as which flex plate is right for the 6.2. I got a blind spot on mine and I want to get the right...

I did some research and found there are two flex plates available for the 6.2, one is GM P/N 14077157 which Crash mentioned and the other one is GM P/N 14077158. Okay here is the question what is the difference between both flex plates? Is one normal and the other a heavy duty version? They both...

Hey Aaron1009 are you still looking for a radiator? I bought a brand new one in it's original box on ebay from a surplus dealer for $150 (buy it now) plus $35 for shipping to Georgia from California. He has some more for sale right now, here is the ebay item number : 330436276908. It took just...

Leaving Moody afb this morning I spotted a M1009 in great shape at the main gate, does anyone here at SS own a M1009 and is stationed at Moody afb, GA? Cheers:beer:

Read through and see that not much has changed except for the modern bodys styles between the CUCV and CUCV II, two alternator set up,etc. Cheers :beer: http://www.gmfleet.com/pdf/2001-2002LSSVOwnersManual.pdf http://www.gmfleet.com/pdf/2003EMPOpmanual.pdf...

Great job! I like the grey interior, looks much better than the old burgundy interior. What do you have mounted on the dash? Is it the rear view camera or the GPS? Cheers

Hello, has anyone ever used the diagnostic connector below the dash on the M1009 to troubleshoot their vehicle or know how it is used? Is a specific diagnostic tool required? Cheers :beer:

NHTSA Campaign Number:83V107000 Vehicle/Equipment Make:CHEVROLET Vehicle/Eqipment Model:BLAZER Model Year:1984 Mfg Campaign Number: Mfg Component Desc:SERVICE BRAKES, HYDRAULIC:FOUNDATION COMPONENTS:HOSES, LINES/PIPING, AND FITTINGS Mfg Involved in Recall:GENERAL MOTORS CORP. Manufacture...

Belive it or not, , there is a grove around the u joint cups and on the shaft where the cups go. The cups are held in place using a plastic ring. The aftermarket u joints have clips and you can get then with or without grease fittings. Hope this helps.

You are probably tired of listening to motor by now, especially after a few miles! Go to crutchfield and look up Item #176GM16 it will help you with the radio instalation. The radio will be installed right below the volt meter, be prepared to do some cutting nothing major. You could also use...

A new voltage regulator resolved my problem, no more flashing GEN 2 light. Cheers:beer:

It was the heat sheild, thanks for the input guys.

When I first bought the truck, one of the first of many PROBLEMS :-D with the truck was the left hand bolt that holds the pump to the bracket was dragging on the pulley. Thanks for the input Mike.

I am having a difficult time locating the source to a metalic rattleing noise coming from the engine in my M1009. It sounds like it is coming from the front of the engine, even worse when the engine is hot. Has anyone ever experince this on their 6.2's? Cheers